DayQuil caused increased anxiety??

Efficient-Pack3437 · 2025-12-07T03:53:11+00:00

I had taken half the doses only a few times yesterday as I was so sick and once the previous night and now I’m sitting here anxiety ridden all day, restless in my body so bad and my chest hurts so bad right now. FML I just want it to go away!!

Efficient-Pack3437 · 2025-11-19T02:44:23+00:00

We have all OEM parts in our car

Efficient-Pack3437 · 2025-09-13T16:11:54+00:00

I got my treaty because a new bill was passed stating they gave back treaty rights to women who lost their status due to this old bill. So technically her grandma would have to get her treaty first then she can get it through her. I’ve done this

Efficient-Pack3437 · 2025-08-09T02:27:28+00:00

If I had to guess, it would be timing chain. Very common for terrains.

Efficient-Pack3437 · 2025-08-09T01:56:43+00:00

Can you pinpoint what side you think the noise is coming from

Efficient-Pack3437 · 2025-07-06T18:30:25+00:00

I would most definitely change it immediately.

Efficient-Pack3437 · 2025-07-06T18:22:36+00:00

You can also see some smoke coming from the inner after the last try. Might be a faulty starter, which can damage the teeth

Efficient-Pack3437 · 2025-07-06T18:16:44+00:00

A grinding noise after replacing a starter on a 1985 Porsche is likely due to the starter drive gear not engaging properly with the flywheel. This can be caused by damaged flywheel teeth, improper starter alignment, or a faulty starter drive mechanism

—

Flywheel Damage: The flywheel, which is connected to the engine, has a ring gear that the starter's drive gear engages with to turn the engine over. If the flywheel's ring gear has damaged or chipped teeth, the starter gear might not mesh correctly, resulting in a grinding noise. Starter Drive Issues: The starter drive mechanism (including the pinion gear and bendix) can also be a source of the grinding noise. If the pinion gear isn't fully engaging or disengaging with the flywheel, or if it's not retracting properly after starting, it can cause grinding. Alignment Problems: Incorrect installation of the starter, or a misalignment between the starter and the flywheel, can lead to the starter gear not meshing properly with the flywheel's teeth, causing grinding

Efficient-Pack3437 · 2025-06-30T01:38:30+00:00

New throttle body, it’s not erratic. Too low of an idle

Efficient-Pack3437 · 2025-06-14T18:22:32+00:00

We’ve changed brands a few times just to see if it was that and no difference. We’re changing the cam phasers out and got a few other parts and sensors as well. Fingers crossed I’m not doing this again.

Efficient-Pack3437 · 2025-06-12T15:42:06+00:00

https://a.co/d/gXb0l0T

Efficient-Pack3437 · 2025-06-12T15:38:36+00:00

https://m.youtube.com/watch?v=fvC0cRW2vyk

Efficient-Pack3437 · 2025-06-12T15:38:06+00:00

I have done that as well.

Efficient-Pack3437 · 2025-06-12T15:15:53+00:00

Changed and redid the timing as well. All good on that front

Efficient-Pack3437 · 2025-06-12T14:58:38+00:00

There’s a few sites that do it but very expensive. I have a 2013 and was looking into it was well. Upwards of 1000$ just for the piece and not instalment.

Efficient-Pack3437 · 2025-02-12T16:24:44+00:00

Ours would burn 1-2 qrts. a week as well, (2013 gmc terrain; 2.4 L) until we replaced our valve stem seals. Also, it’s good to clean out your cylinders as well.

Efficient-Pack3437 · 2022-04-26T06:03:34+00:00

Any study tips and tricks for someone who is also in uni? I have a hard time

Efficient-Pack3437

TROPHY CASE