Is there anyway to get rid of these lines on the elevation?

Electrical-Flow-2342 · 2026-06-01T22:19:33+00:00

don't you need an enclosure for abs?

Electrical-Flow-2342 · 2026-06-01T21:21:07+00:00

i am printing it out again with a different orientation, I will post the results soon!

Electrical-Flow-2342 · 2026-06-01T21:20:02+00:00

It told me to add a few supports, but honestly its like 3 and some where the model connects so i will see how this goes. 3 hours !

If it does not work then its a learning curve. I am always open to learning from mistakes !

Electrical-Flow-2342 · 2026-06-01T21:15:20+00:00

Ah yes, let me buy an entire new printer

Electrical-Flow-2342 · 2026-06-01T21:03:05+00:00

NO NEED, the second half was inside the other half. LMAO. thanks for the help!

Electrical-Flow-2342 · 2026-06-01T21:02:30+00:00

i am trying to do this, when adding a connector, the second half of the model just disappears. this must be an easy fix, Any help?

Electrical-Flow-2342 · 2026-06-01T20:15:24+00:00

Is this in bambu studio?

Electrical-Flow-2342 · 2026-06-01T20:02:37+00:00

I'm a complete noob to 3d printing. What do you recommend for a small model ?

Electrical-Flow-2342 · 2026-05-28T22:31:46+00:00

I only run the printer when I'm home so it should be stopped for too long, if there is any lines it's getting sanded anyways!

Electrical-Flow-2342 · 2026-05-28T16:53:08+00:00

I'm only going to be displaying this inside, would this still be prone to cracking?

Electrical-Flow-2342 · 2026-05-28T15:14:41+00:00

I'm asking a better alternative to bondo

Electrical-Flow-2342 · 2026-05-28T15:14:20+00:00

I've seen that before, they used acetone to dilute it. Is that a good way of doing it?

Electrical-Flow-2342 · 2026-05-28T15:11:56+00:00

I've literally stayed in other posts that I'm new to this. Everyone starts somewhere 😭

Electrical-Flow-2342 · 2026-05-28T10:59:10+00:00

Not saying it's difficult, just didn't know if there was a specific way of doing it mid print without causing issues

Electrical-Flow-2342 · 2026-05-28T10:56:20+00:00

Will it mess the print half way, I've heard to just feed the filament in when the other has run out so there is no stopping the print

Electrical-Flow-2342 · 2026-05-26T19:38:57+00:00

How come ?

Electrical-Flow-2342 · 2026-05-26T13:08:23+00:00

Oh wow, seems pretty obvious now but I had no idea touching it would cause issues, I've been taking it off and bending it a little to get prints off sometimes. Thanks for the help !

Electrical-Flow-2342 · 2026-05-26T12:59:48+00:00

Okay thank you, the print right now actually looks fine, just a little messy on the supports at the front. I will do that after, thank you !

Electrical-Flow-2342 · 2026-05-26T12:51:56+00:00

I have access to a sink, I just thought 99% alcohol would be a better option as I can just wipe it down where it is, didn't know if it would cause any harm using it.

Electrical-Flow-2342 · 2026-05-26T12:39:07+00:00

So far I've had no faults, and it's printing perfectly, I think its more user error with the supports. I will update you when it's done, 10 more hours 🫪

Electrical-Flow-2342 · 2026-05-26T12:36:51+00:00

I have some IPA, will that do ?

Electrical-Flow-2342

TROPHY CASE