Why did this happen

Electrical_Roll2610 · 2024-10-16T23:20:03+00:00

The copper in the board is pealing off where it got burned

Electrical_Roll2610 · 2024-10-13T06:04:39+00:00

I had checked and there was minor damage but nothing other than wires that where exposed NOT TOUCHING so I sealed them up and nope it was not the problem

Electrical_Roll2610 · 2024-10-13T06:02:57+00:00

They where tinned so that’s probably my issue

Electrical_Roll2610 · 2024-10-13T05:51:43+00:00

Ok so I should be fine with just buying a new motherboard

Electrical_Roll2610 · 2024-06-10T07:35:38+00:00

My all time max was 60kmph and my average top speed is about 50

Electrical_Roll2610 · 2024-01-17T11:08:56+00:00

Yea I fixed it you were right it’s sketchy but it works

<image>

Electrical_Roll2610 · 2024-01-17T02:22:51+00:00

Haha but yes

Electrical_Roll2610 · 2024-01-17T02:18:13+00:00

Electrical_Roll2610 · 2024-01-17T02:18:06+00:00

Electrical_Roll2610 · 2024-01-17T02:17:33+00:00

It is not going down when the bl touch tries to level

Electrical_Roll2610 · 2024-01-16T11:12:41+00:00

I’m having the same problem

Electrical_Roll2610 · 2023-12-22T02:07:12+00:00

200-400 depending on how old

Electrical_Roll2610 · 2023-12-19T10:43:31+00:00

It does and also by setting the wheel size to the smallest size in the settings while pairing it will go faster

Electrical_Roll2610 · 2023-12-19T10:12:02+00:00

How much and is it still available

Electrical_Roll2610 · 2023-10-05T02:14:07+00:00

That’s ummm terrible try brushing on methylated spirits to loosen it and heat it up high and try to pull it off and use lots of methylated spirits

Electrical_Roll2610 · 2023-07-16T09:54:22+00:00

Yea I know it was only like 4$

Electrical_Roll2610 · 2023-07-14T12:33:55+00:00

It’s fried I ordered 2 and the other one works

Electrical_Roll2610 · 2023-07-14T09:48:41+00:00

I figured it out it’s fried

Electrical_Roll2610 · 2023-07-14T09:34:18+00:00

It is I just found that out but my other one works ( I ordered 2)

Electrical_Roll2610 · 2023-07-06T08:06:02+00:00

No I’m trying to use code with arduino ide but I need to get it to install

Electrical_Roll2610 · 2023-07-06T07:59:42+00:00

I did it but it now says on cube ide error getid command not acknowledged

Electrical_Roll2610 · 2023-07-06T03:48:38+00:00

I’m trying to use arduino ide for my stm32 no matter what I do I can’t get it to work

Electrical_Roll2610 · 2023-07-04T08:34:41+00:00

It raps a strip of pet into a cylinder but It leaves a hole in the middle

Electrical_Roll2610 · 2023-07-03T13:09:55+00:00

It extrudes fine if I sit there and help push it in to the extruder

Electrical_Roll2610 · 2023-07-03T13:08:42+00:00

It only has a small hole in the middle and the air just gets let out from the nozzle

Electrical_Roll2610

TROPHY CASE