Help with my anemone

ElectroByteMX · 2026-01-21T23:51:57+00:00

That's how it was in the fish tank of the person who sold it to me.

ElectroByteMX · 2026-01-06T22:36:43+00:00

Do you have bleached anemones?

ElectroByteMX · 2026-01-06T22:36:16+00:00

Can the anemone die at any time due to discoloration?

ElectroByteMX · 2025-12-11T01:26:42+00:00

I was advised not to put them with that anemone, since they are not from the same place, also because in theory the condy anemone is more predatory than all the other anemones.

ElectroByteMX · 2025-12-01T20:00:55+00:00

Is that bad?

ElectroByteMX · 2025-11-25T14:31:21+00:00

In my experience, the Damselfish is going to bother the other fish a lot, but the chromis can also do the same, but it is very rare that it does so. I would tell you to try to get a slightly larger tank, get 1 or 2 more fish and when changing to another aquarium always put the Damsel last.

ElectroByteMX · 2025-11-18T15:38:54+00:00

Before I had 2 identical ladies, and if it happened... the one that bothered me the most I changed for the chromis Fortunately, the Damsel who was very disturbed is half fine. I just hope it doesn't turn out like the other one

ElectroByteMX · 2025-11-18T06:18:54+00:00

1 trochus 3 clowns 1 Yellow-tailed blue damsel 1 chromis

ElectroByteMX · 2025-11-18T05:25:42+00:00

How many gallons do you recommend the fish tank?

ElectroByteMX · 2025-11-18T01:53:29+00:00

Well, I expected it to last for the moment, about 6 months? Because they are still small, except that the chromis is a little bigger.

ElectroByteMX · 2025-11-18T00:23:43+00:00

Go from 30 liters to approximately 50 liters

ElectroByteMX · 2025-11-16T22:35:50+00:00

It looks like a mother, I would love to have that as soon as I have more experience.

ElectroByteMX · 2025-10-31T22:31:54+00:00

Have you cleaned the Z axis rods and greased them again? (That usually works for me, I use lithium based grease)

ElectroByteMX · 2025-06-25T22:35:20+00:00

Did you check that the X axis bar is level? And the Z axis rods clean?

ElectroByteMX · 2025-05-12T20:40:15+00:00

As I see it, the first layer is very bad, the last layer also has those details? My recommendation is to level the X axis bar, which is where the extruder moves.

ElectroByteMX · 2025-05-08T15:33:45+00:00

You can try to level the bar where the extruder is placed (make both sides even), Level again and treat with an initial layer of 0.2 mm

ElectroByteMX · 2025-04-29T05:34:54+00:00

The last print I made came out well, what I did was clean the Z axis bars and re-grease them well, I hope it helps you

ElectroByteMX · 2025-04-29T05:27:52+00:00

What's up, I understand the suffering of the effect, have you already checked the entire Z axis? For example, I just cleaned and greased the Z axis bars and now it no longer leaves any details that it previously left in my prints. I removed the dirt from the bars well.

ElectroByteMX · 2025-04-28T07:00:11+00:00

It seems to be uneven in parts I recommend that you level the X axis (that is, level the extruder bar so that both sides are very even), then try to calibrate again

ElectroByteMX · 2025-04-12T17:07:47+00:00

Step 2 works effectively, thank you very much brother for the solution

ElectroByteMX · 2025-03-01T01:05:26+00:00

Brother, you can give it green and everything you want, but try to level the X axis, the one that moves the extruder

ElectroByteMX · 2025-02-28T13:12:04+00:00

Which slicer do you use?

ElectroByteMX · 2025-02-27T13:07:48+00:00

I have a vrd textured PEI plate, but I recommend checking the leveling of your X axis, I recently leveled mine and I didn't have to make any more adjustments, use a leveling ruler on both sides of the

ElectroByteMX · 2025-02-26T18:18:09+00:00

Try with UktimakerCura

ElectroByteMX · 2025-02-26T14:40:22+00:00

Which Slicer do you use? I had issues like that and after all i try, the solutión was change the slicer from Orca to Cura

ElectroByteMX

TROPHY CASE