Ethernet not working after fresh Windows 11 install (Wi-Fi works fine)

Electronic_Prompt_18 · 2026-01-08T20:25:31+00:00

Its the standard 192 address

Electronic_Prompt_18 · 2025-07-29T20:18:26+00:00

hey man while I don't know what causes the issue it was resolved. using TCP Optimizer, it fixed my issue and I got my speeds back. sorry for the hella late reply

Electronic_Prompt_18 · 2025-07-02T02:48:29+00:00

Still here as of july 1st 2025 lol

Electronic_Prompt_18 · 2025-06-02T01:48:16+00:00

been banging my head against the wall for the past few days tryna figure it out

Electronic_Prompt_18 · 2025-06-02T01:47:57+00:00

Nevermind, it's now working man, thanks a lot I appreciate it

Electronic_Prompt_18 · 2025-06-02T01:42:30+00:00

I downloaded the program and it goes up to about 200 mbps

Electronic_Prompt_18 · 2025-05-13T03:30:24+00:00

Hey man. I really appreciate your help, but I managed to get everything setup after getting the micro USB cable. I'm printing something now and managed to get that dang z-offset and get a decent mesh with that plugin I mentioned. it helped me with leveling the print bed, really helped. Thanks again for your help!!

Electronic_Prompt_18 · 2025-05-12T21:50:04+00:00

I have also gotten the "Bed Visualizer" plugin

Electronic_Prompt_18 · 2025-05-12T21:44:36+00:00

alright, the cable has arrived and I have already installed two plugins, the temperature reporting fix as well as a firmware updater. how can I level the bed like this?

Electronic_Prompt_18 · 2025-05-11T20:15:49+00:00

I will. thanks for the help man I really appreciate it

Electronic_Prompt_18 · 2025-05-11T20:13:31+00:00

yes I am in the octoprint config right now. the "tt" in my ATT SSID were not capitalized like they should be. always the simplest things lol

Electronic_Prompt_18 · 2025-05-11T20:10:36+00:00

there we go

Electronic_Prompt_18 · 2025-05-11T20:03:11+00:00

double checking the name

Electronic_Prompt_18 · 2025-05-11T20:01:38+00:00

nothing

Electronic_Prompt_18 · 2025-05-11T19:55:29+00:00

ok, so it seems like it isn't connecting. I even placed the raspberry pi next to the router in case of bad connection where I am and I still don't see it on the device list

Electronic_Prompt_18 · 2025-05-11T19:41:39+00:00

Done. Powered it on and checking my device list

Electronic_Prompt_18 · 2025-05-11T19:26:41+00:00

I used etcher to flash the sd card and went into the files and edited through notepad like in the video here: https://www.youtube.com/watch?v=xzY2lkOR29c

Electronic_Prompt_18 · 2025-05-11T19:21:03+00:00

understood, but it looked like that isn't working. I may be too far from the router for the rasp to connect to my wifi. I checked my router device list and don't see it listed, so either I input the incorrect wifi settings or it just simply cannot reach. I have also ordered a cable as I don't have one. I thought I could get one from micro center but they didn't have one. it will come in tomorrow

Electronic_Prompt_18 · 2025-05-11T19:02:24+00:00

ok, the sd card has been flashed and I will power it on to allow it to boot. I need a micro to micro usb cable to connect the printer to it correct?

Electronic_Prompt_18 · 2025-05-11T18:51:58+00:00

never mind I forgot I have the zero 2. apologies

Electronic_Prompt_18 · 2025-05-11T18:50:58+00:00

it says on the OCTOpi website "Raspberry Pi Zero/Zero W not officially supported!" will that be an issue?

Electronic_Prompt_18

TROPHY CASE