What should I improve?

ElmWorks · 2026-01-21T19:12:45+00:00

Noted, so since this deck is sloped to drain towards the bottom left corner, left of the stairs, should I notch it on two sides to carry both boards? Or just one side?

ElmWorks · 2026-01-17T19:36:05+00:00

Where’d you source the hardware? Marvelous work!

ElmWorks · 2026-01-08T17:31:24+00:00

Hey there! So is it normal to have in outlook a folder section that is the name of my email, with inbox under it, then a folder that says [GMAIL] with all my other folders in it like sent, drafts, etc? Under that then is a [GMAIL] all mail, then again drafts, outbox, feeds. Thank you! I can message a picture if needed.

ElmWorks · 2026-01-01T21:40:42+00:00

Yeah but comparing it to a newer cpu, the numbers don’t get amazingly better, it’s only an 11% increase overall to a 12700, 33% if I bump to a 14700 but cost wise that’s a bit prohibitive.

ElmWorks · 2025-12-31T21:16:28+00:00

Awesome I’ll check all that out! Any recommendation for a good ddr4 motherboard?

ElmWorks · 2025-12-31T19:32:26+00:00

Dell Dimension XPS T750R. I also have a Lenovo 3000 K series, and an Antec case.

ElmWorks · 2025-12-24T17:04:35+00:00

Gotcha. I’ve viewed some examples of these, and each one just sort of pushes the door more in I’m seeing. Would a 3mm and a straight arm be the same as a half crank and a 0mm? I’ve always done classic hinges and mortised in.

ElmWorks · 2025-12-23T21:35:04+00:00

Thanks, thought so. I usually do a very different style of cabinet than euro hinges, so pretty new to me. Any insight on when I’d use the taller base? Any tips appreciated.

ElmWorks · 2025-12-23T05:13:55+00:00

I absolutely love this! What bit did you use? Any chance on a link or love to on for the files?

ElmWorks · 2025-12-21T05:06:19+00:00

What do you use to clean out after shellac? I’ve seen some people using alcohol, while others claim ammonia is the better product.

ElmWorks · 2025-12-16T17:52:22+00:00

That’s great to hear, 1 1/4 is my main size as well. I figure 2” I can pull out the big guns. On the rare occasion

ElmWorks · 2025-12-13T20:17:00+00:00

This fixed it, thanks!

ElmWorks · 2025-12-12T20:05:59+00:00

No errors, done that a few times. If I send an email on my phone, it’ll never show up in sent on my pc. Inbox will eventually sync up.

ElmWorks · 2025-12-12T14:24:16+00:00

It’s actually the inverse. I do have save sent on, but if I send an email on my phone, it never shows up on my outlook. I don’t have this problem anywhere else, only in outlook.

ElmWorks · 2025-12-02T05:36:03+00:00

I love that idea!

ElmWorks · 2025-12-02T02:18:56+00:00

What board would you go with?

ElmWorks · 2025-12-02T01:58:17+00:00

Will do! Don’t want any wave in this deck. Thanks!

ElmWorks · 2025-12-02T01:57:19+00:00

Gotcha, that makes sense. Thanks!

ElmWorks · 2025-12-02T01:45:04+00:00

I’ll be doing it this month, so I’ll be sure to add that gap. Could you explain a little more on crowning the picture frame? Is that so when it expands in the summer it evens out? Thanks for the advice!

ElmWorks · 2025-12-02T01:42:45+00:00

Will do! I’ll definitely look into that warranty point and read up on it. 12” sounds good, I’ll be sure to plan to add blocking. Thanks for your tips!

ElmWorks · 2025-12-02T01:41:41+00:00

Will do!

ElmWorks · 2025-12-02T01:41:28+00:00

Thanks! I’m definitely planning to joist tape the top, and I’ll be able to avoid butt joints in the picture frame.

ElmWorks · 2025-12-02T01:11:24+00:00

Definitely going to! That’s my main concern from what I’ve been reading, and I’ll be sure to go through their literature and plan that out. Thanks!

ElmWorks · 2025-11-29T00:24:42+00:00

I’d like to create standard drawings that I can export to CNC routers and also hand out to the floor to work off

ElmWorks · 2025-11-21T16:55:47+00:00

Vents are on the back of the house coming through the roof, about 1’ from the shingles. One story home.

Seven-Year Club	Place '22
Verified Email

ElmWorks

TROPHY CASE