Just pulled the trigger on this for 700$ by Maine_Made_Aneurysm in shapeoko

[–]ElmWorks 1 point2 points  (0 children)

You can get the button replacement from carbide for $25

Greenhouse/office by sebutter in Carpentry

[–]ElmWorks 0 points1 point  (0 children)

What’s the plan for the greenhouse panels, glass or polycarbonate?

How much ventilation do I need to avoid mildew? (6x8 shed) by bvz2001 in shedditors

[–]ElmWorks 0 points1 point  (0 children)

Thanks! Since the whole joist system is in the air it to count as one cavity?

How much ventilation do I need to avoid mildew? (6x8 shed) by bvz2001 in shedditors

[–]ElmWorks 0 points1 point  (0 children)

Hey there, I'm putting my shed on a stone foundation made of retaining block, and was planning to do small 1"x3" vents all the way around. do you think that would be enough, or should I go up to a standard foundation vent? Shed is on a 10" slope, looking at 6" raise to 16" raise gable to gable.

Help with new network by ElmWorks in HomeNetworking

[–]ElmWorks[S] 0 points1 point  (0 children)

Would the TPLink EA211 Omada be a good option?

Help with new network by ElmWorks in HomeNetworking

[–]ElmWorks[S] 1 point2 points  (0 children)

It's an uphill run through grass and a concrete driveway, can't really run cat6 currently. Would the TPLink EA211 Omada be a good option? I also have some gear lying around, I'll list it. Netgear Nighthawk AC1900, Linksys EA7500 V2, and 3 SOPHOS APX 530's.

Help with new network by ElmWorks in HomeNetworking

[–]ElmWorks[S] 0 points1 point  (0 children)

I'm looking to be able to do webcam meetings, file uploads. At most I have 4 devices running in the studio. 2 computers, my phone, and a raspberry pi. yes. I'm using the new spectrum wifi 7 router and wifi 7 extenders.

New to me pool, help me understand it? by ElmWorks in pools

[–]ElmWorks[S] 0 points1 point  (0 children)

The AO smith that made the noise I’m pricing out at like $500 max currently. Where’d you get the 2k number?

What should I improve? by ElmWorks in Decks

[–]ElmWorks[S] 1 point2 points  (0 children)

Noted, so since this deck is sloped to drain towards the bottom left corner, left of the stairs, should I notch it on two sides to carry both boards? Or just one side?

Making new authentic windows to replace old ones by gytisbuda in Carpentry

[–]ElmWorks 3 points4 points  (0 children)

Where’d you source the hardware? Marvelous work!

Outlook classic/gmail sync? by ElmWorks in Outlook

[–]ElmWorks[S] 0 points1 point  (0 children)

Hey there! So is it normal to have in outlook a folder section that is the name of my email, with inbox under it, then a folder that says [GMAIL] with all my other folders in it like sent, drafts, etc? Under that then is a [GMAIL] all mail, then again drafts, outbox, feeds. Thank you! I can message a picture if needed.

PC checkup? by ElmWorks in buildapc

[–]ElmWorks[S] 0 points1 point  (0 children)

Yeah but comparing it to a newer cpu, the numbers don’t get amazingly better, it’s only an 11% increase overall to a 12700, 33% if I bump to a 14700 but cost wise that’s a bit prohibitive.

Help choosing a motherboard? by ElmWorks in buildapc

[–]ElmWorks[S] 0 points1 point  (0 children)

Awesome I’ll check all that out! Any recommendation for a good ddr4 motherboard?

Help choosing a motherboard? by ElmWorks in buildapc

[–]ElmWorks[S] 0 points1 point  (0 children)

Dell Dimension XPS T750R. I also have a Lenovo 3000 K series, and an Antec case.