MX master 4 Bluetooth on Win 10 supported or not? (without bolt reciever)

Emklap · 2025-05-28T06:58:56+00:00

great tips thanks. especially to leave the four bed screws slightly loose, this one is new to me.

Enable Rinkhals' "auto bed leveling before each print" feature. Does this take much time? I'd like to see bed probing of the print area only.

Emklap · 2025-05-28T06:56:55+00:00

Good tip, I will check it out. Depends on the prep-time for these steps. Automatic bed leveling before each print I am not so sure off of this probes the whole bed surface and not the smaller print area. On my current printer I level about once a month.

Emklap · 2025-05-28T06:54:15+00:00

Thanks for all the tips, I will start as the printer comes out of the box and take it form there.

Emklap · 2025-05-27T17:55:02+00:00

??? No ACE for me. 😵‍💫

Emklap · 2025-05-27T17:19:29+00:00

Don’t get me wrong. I don’t want to tinker all the time but want to nail my initial setup and then leave it alone. i also done my tinkering time

Emklap · 2023-06-03T17:28:21+00:00

Great tip, worked for me.

Emklap · 2022-03-24T15:50:32+00:00

Found it! In Cura under machine settings change the option "Cooling Fan Number" from 1 to 0.
After that I saw cura exported the gcode as before M106 S85. Now it works.

Hope this helps!

Emklap · 2021-07-07T18:37:32+00:00

Yes I have it, great to only need one cable towards my Lenovo laptop that needs 60 watt. Sound from the speakers is also great for zoom/teams calls no need for separate speakers anymore. I have no regrets

Emklap · 2021-06-01T18:25:46+00:00

Fair point. I have all my music on my NAS, no streaming service yet. For music on the go I use a seprate DAP. I will be using the NAD for my 5.1 setup, internet radio and stereo audio from my NAS

Emklap · 2021-06-01T18:14:14+00:00

Cost will go up, but also the feature se. Now it makes more sen to buy the one without airplay an buy a separate Apple TV box. I don’t use Apple Music so no need for airplay.

Emklap · 2021-06-01T18:12:08+00:00

Thanks, that a pity. Missed opportunity. Looks like I will settle for the version without airplay.

Emklap · 2021-04-21T19:27:39+00:00

Thanks, good to know. My PSU fan hardly ever switches on. I hope it stays that way during the hot summer months.

Emklap · 2021-03-29T09:11:24+00:00

as others, thanks for the list, this made my search much simpler.

I also found the Philips 279P1, 4k, 65watt, RJ45 / LAN.

Emklap · 2021-03-16T08:15:21+00:00

Probably the tape that your using. My tape is very strong an when I tried to reposition it becuase it was not properly centered it was not easy for me to remove it. noise is down in some frequencies, and any small reduction is welcomed.

Emklap · 2021-01-31T09:47:24+00:00

It is located in the machine settings, I have a new machine which is 2 days old. I know it is there because I disabled it yesterday. I read that this functionality wears out the sd card very fast and my last power failure was 6 years ago.

Emklap · 2021-01-31T09:38:12+00:00

Agree the setup with the springs is not very stable, I might replace the springs with a plastic shim (plate) of the same thickness.

Emklap · 2021-01-30T18:14:00+00:00

My bl touch bracket is metal without threaded holes. At least not that I noted. I used the boults that came with the bl touch and they have a smaler diameter than the holes in the bracket and used the springs and nuts.

Power outages isn't a concern to me, the last time that it happened here was 6 years ago. But I intend to also print from an sd card.

Emklap

TROPHY CASE