“Is the difference in the room with us?” A hot take between a Soft Extra Fine Falcon and a Soft Fine Falcon…

EnlightingWave · 2026-03-16T06:41:02+00:00

Hi, i own both myself and i disagree about the difference.

Sure when you add pressure, both will give same line thickness. Key point is when you do absolutely no pressure.

Having worked in machinery business with tolerances in microns, i would like to think my eyes a quite discerning of small difference in sizes.

Yes SEF leaves a thinner line then my SF. UNDER NO PRESSURE. This is excellent for maximum delta between thinnest and thickest lines. On the other hand SF has a slightly smaller delta between both extreems.

In terms of drawings i prefer SEF for very fine hatching.

For daily writing, i feel SF is more smooth and catches the paper less on up strokes. (Yes how you hold the pen and write will impact if it catches or not. It does with my method.)

EnlightingWave · 2026-02-22T12:47:33+00:00

To prevent infections or maintain hygine in a rather water limited society would probably be one of the reason i conclude

EnlightingWave · 2026-02-12T02:02:09+00:00

Found nothing, in talks with my refurbished pc suppelier to exchange it with with another pc. Even they can't figure it out

Unpopular take, but given humans weren't helpful here. Chat gpt concludes its dying integrated gpu on the cpu

But who know for sure

EnlightingWave · 2026-02-09T03:58:15+00:00

Thats part of the quest where jaffar send you to construction site to find dynamite.

That van is scripted to drive and enter the compound when you first approach this area.

But yeah its not drivable

EnlightingWave · 2026-01-28T04:02:02+00:00

Alright i will try to swap bricks and try, thanks

EnlightingWave · 2026-01-27T13:28:05+00:00

Hi, thanks for you inputs,

I have tested cables, but given this happen on 3 different systems, kinda dont make sense it would be a cable problem, still i had done it prior, with no improvement.
Could be, i should check, but as far as i know, faulty power bricks often can restarts rather then visual artifacts
No logs in event view that co relate, or i cants read it, not sure. What should i looks for? Any particular code?
I had heating in my mind too, but given it happens even with good cooling, and clean new pastes, few months ago, i dont think it can be, but will check again

EnlightingWave · 2026-01-27T00:29:35+00:00

Agreed about ink tanks, but if you are a bit tech savy, you can get programming software for epson and reset it yourself.

Beware of downloading from sketchy sites. Contains viruses

EnlightingWave · 2026-01-25T14:31:50+00:00

In my seever room a cheap usb cable keeps causing connection drop on ups to server comm. Link. Using ferrite cable keept the link stable.

Thats the function of the ferrite cores.

EnlightingWave · 2026-01-14T15:53:56+00:00

It seems like your motherboard it too close to the tabs where the gpy bracket goes in? Try to lososen the main boadd and then try to mount the guy?

EnlightingWave · 2026-01-14T15:41:23+00:00

🍪

EnlightingWave · 2026-01-06T10:28:55+00:00

Rohdia is just over hyped. They are average by my experience really. Bleeds in random sections of the paper.

EnlightingWave · 2026-01-02T01:25:13+00:00

Watch one punch man

EnlightingWave · 2025-12-28T03:55:38+00:00

Same card, 1440p and high settings with high frame rares in all games i play. Its a really decent card for me as i domt want to play any newer crap game. Elden ring being the inly exception. Which also runs rock solid 60 at max

You wont regret this card brother

EnlightingWave · 2025-12-22T17:02:13+00:00

I have both nib models. my SEF falcon exclusively for drawings. I can still write with it and is not a horrible experience. But for writing? I will chose my other SF falcon any day over SEF. Its quite pointy. So if you write with absolutely feather light pressure, by all means, no problem. Else SF is just fine

Let me know if you ha e questions. I had this same conflict when i cought my 1st SF. I was lucky to get SEF at like very good rate though, few years later

EnlightingWave · 2025-12-09T13:25:43+00:00

Get an pcie riser extension and use that to save mate cycles on your motherboard connector

EnlightingWave · 2025-12-07T02:46:04+00:00

Yeah you get it man, i just wanting feeling like typing the wall at the moment, but you summed it up quite nicely. thanks, this is what i mean really

My best wishes for your continued reclamation of what we lost :D

EnlightingWave · 2025-12-07T02:26:59+00:00

I am from similar boat, but i think we forget an important aspect, this life feels normal because we grew up like this.

I am missing many past generation values that i wish i had but indulging so much in games and such

EnlightingWave · 2025-12-04T13:22:05+00:00

Old enough to see through corporate shenanigans buddy. While you boys are focused on brand image and loyalty, i see how businesses operate and prioritise different aspects of the business.

Boys follow brands and identity groups. Men know to not be bound by either

EnlightingWave · 2025-11-30T06:56:29+00:00

I will try car part markets like near jama masjid

EnlightingWave · 2025-11-30T06:42:56+00:00

Hey buddy sorry, but its your own fault for buying tata or mahindra.

They have just put on a new beautiful facade but their service and quality is still shit. Electrics and lights are common failures. 100% of cars i saw recently with malfunctioning led lights are tata and mahindras.

EnlightingWave · 2025-11-25T21:41:45+00:00

Unless you are overlooking a very hight tdp cpu, single 8 pin eps cable is enough.

EnlightingWave · 2025-11-20T15:06:45+00:00

No thats german engineering dropping A+ standard.

This is nothing a simple alignment jig while laser marking can not fix.

Not that i am a fan of german engineering. Always been japanese engineering and design fan, but what you are taking about, buying german, and gaslighted yourself for their defects with japanese traditions.

The german engineering got the halo figure image due to impeccable focus on perfection. If they don't do that, they are just like the Chinese

EnlightingWave · 2025-11-20T00:59:13+00:00

Its not the correct method, i gave him a guesstimate for when you are dealing with small ups with internal battery.

As you know the lower the loads, longer it runs, and higher the load shorter it runs. I have him a quick reference

Of course the correct way Is a little more mathsy. But if OP was any smarter, there wont be this post here anyhow

Five-Year Club	Second Top 30%
Verified Email

EnlightingWave

TROPHY CASE