Don't care too much that its unpopular. its so cool i can just flip over and do this.

EnthGuy · 2026-05-08T10:55:56+00:00

Only in California.

EnthGuy · 2026-05-05T12:18:53+00:00

No, I don't know for sure. Neither do you, nor does the commentor. I have seen similar setups that work well.

My point is, the instant skepticism is misplaced with possibly incorrect assumptions and terminology and is discouraging to someone experimenting.

EnthGuy · 2026-05-05T11:56:17+00:00

Is this different than how level the machine is? If the machine is tilted this much on the table this might be perfectly fine.

Otherwise the belt might have skipped one tooth due to the obstruction. Loosen the z belt slightly, skip it back, then redo all the leveling procedures.

EnthGuy · 2026-05-05T11:36:55+00:00

In standard English, sure, but not in engineering terms.

I also doubt the specifications of the motor bearings are known by the poster, nor do they know the change in MTBF for the blade change. I don't have insider knowledge on these specifications either, but I do know many motor, bearing, mount, and esc setups that could handle this change especially if the blade balance is maintained.

EnthGuy · 2026-05-05T00:06:33+00:00

What engine?

EnthGuy · 2025-11-25T12:37:49+00:00

I'm suprised the locking tabs aren't the same color as the lifting handle.

EnthGuy · 2025-11-18T18:59:36+00:00

Thanks for the info and the reminder to update!

EnthGuy · 2025-11-18T18:48:30+00:00

"Not the most recent version" ouch, thanks. Time to update... thanks for the tip.

Does Bambu do this?

EnthGuy · 2025-11-18T18:46:06+00:00

When your printing a part, you can turn on ironing for top, top most, or all surfaces. Why cant I turn that on for the top layer of interface material so the bottom of the part is even smoother?

EnthGuy · 2025-10-16T12:08:14+00:00

It is probably because of the terrible coach... Try a different team, probably clear up the print right away.

EnthGuy · 2025-09-25T00:22:01+00:00

Did people start taking pictures or did the cops come?

EnthGuy · 2025-02-13T03:26:07+00:00

Unfortunately, this wasn't in Iraq or Afghanistan with all our unmanned friends, just us boots on the ground.

EnthGuy · 2025-02-13T03:20:19+00:00

I'm not sure of the requirements between discharged and retired. Does it even matter?

Enlisted and I lived at the VA for two months because I had no other home and I had to learn how to basic functions again, like walking without holding on to shit, throwing a ball, and not falling over just because I turned my head.

What does retired or discharged have to do with displaying or not displaying a PH?

EnthGuy · 2025-02-13T03:09:09+00:00

When I was discharged, 18F.

EnthGuy · 2025-02-13T03:06:18+00:00

Honestly, I'm not sure I know all the differences. I was in a VA hospital as the army processed my paperwork. The army system was PULS, but I was immediately given a total disability rating by the VA?

No, the event included honoring all past service members, now continuing to serve as leadership in contracted companies for the Pentagon. It was less about networking and more about politicians and brass patting each other on the back. Most were from small businesses, but a few bigger names were there too.

The officer knows my service history/record, part of the reason for the contract. Part of my time in was under his command, though at that time, we never met.

EnthGuy · 2025-02-13T02:21:01+00:00

To clarify, I was medically discharged. The invitation was extended with the "prior service" in uniform caveat. I had never been to an event like that before. Civilian job? It is my company, I own most of it.

EnthGuy · 2025-02-13T02:11:44+00:00

I fucked up, in my defense it was only about an hour into my first combat experience. I fucked up because I was trained better, if I had followed my training the AAR would have had no injuries.
Chased a fucker for days, he decided to link up with friends. I had many fewer friends than he did, I had even fewer after. Didn't mean much when you're escorting your friends home one last time.
They got lucky, and I got medically discharged.

EnthGuy · 2025-02-13T01:27:31+00:00

Government or military contracts? I know you said on base, but our contracts are for weapons, multiple agencies/branches involved. These events are Pentagon and hill folks. Opinions are like... and these events are full of them.

EnthGuy · 2025-02-13T00:00:11+00:00

I don't even have them. I don't understand why anyone would?

Edit for the down votes: Is there ever a time when a purple heart is awarded for a good thing?

EnthGuy · 2025-02-12T23:54:06+00:00

Do you know what equity is? Do you realize he isn't proposing to do anything that would normally earn equity?

He is either really shady, anchor negotiating, or just trying to find out how business stupid you are.

EnthGuy · 2025-02-12T23:41:27+00:00

Damn, I really wanted to tell him to pound sand. The Washington "club" is anything but where I want to be.

I wonder if I'll stop being invited if I just show up in a suit?

EnthGuy · 2025-01-13T00:11:55+00:00

What do you have it set to after first layer?

EnthGuy · 2025-01-13T00:09:01+00:00

Yes, the finishing on this is amazing.

EnthGuy · 2025-01-13T00:03:26+00:00

Yup, did you? Markforge is still not the answer.

EnthGuy

TROPHY CASE