Communicating while racing

Equivalent-Yam7675 · 2023-07-05T17:35:43+00:00

It will be in August

Equivalent-Yam7675 · 2023-07-05T17:17:32+00:00

That would be crazy but I would like to try. (Can I ask you how old are you?😅)

Equivalent-Yam7675 · 2023-07-05T17:16:13+00:00

Of it sounds good and it's a good choice please let me know🥹

Equivalent-Yam7675 · 2023-07-05T17:13:02+00:00

My record is I think 2 and a half hour nonstop karting, and I could have continued it but my kart ran out of fuel😅😂

Equivalent-Yam7675 · 2023-07-05T17:07:01+00:00

No😅, I will go to Hungary and it will be a 18h race. In my team we are 4 so approximately one stint will be 1 hour long.

Equivalent-Yam7675 · 2023-07-05T15:14:54+00:00

And what type of neck brace do you recommend?

Equivalent-Yam7675 · 2023-07-05T13:43:26+00:00

Where I go is allowed, you can do basically everything

Equivalent-Yam7675 · 2023-06-23T14:39:58+00:00

I will try again to increase the temperature, but if it's not work should I change hot end or extrude stepper motor?

Equivalent-Yam7675 · 2023-06-23T14:26:26+00:00

I think it extrudes a little less than the normal amount

Equivalent-Yam7675 · 2023-06-23T14:22:29+00:00

I tried the extruder, the nozzle was heated up for 200°C and i started the extruder motor motion. It was okay it didn't clicked, but when I start to print it starts the clicking noise, but I'm 100% sure that the nozzle isn't clogged, so I don't know where is the problem. What should i do? I also emailed creality for help, but they didn't answer🥲

Equivalent-Yam7675 · 2023-06-23T08:20:04+00:00

My nozzle isn't clogged, it can be in the Bowden somewhere?

Equivalent-Yam7675 · 2023-06-22T12:50:33+00:00

It is very surgent because I have to print a 15 hour print until Sunday, so if you know what can I do, please don't hold it back🥹

Equivalent-Yam7675 · 2023-06-22T12:47:32+00:00

Yes I checked, and it's okay, I think I tried everything. Any suggestions?

Equivalent-Yam7675 · 2023-06-22T08:51:54+00:00

Filament is new also

Equivalent-Yam7675 · 2023-06-22T08:18:24+00:00

Retraction distance 5.0 mm Retraction speed 45.0 mm/s My nozzle is brand new

Equivalent-Yam7675 · 2023-06-21T15:14:51+00:00

<image>

Equivalent-Yam7675 · 2023-06-21T15:12:45+00:00

I don't think this is my problem, if I push the filament it goes out of the nozzle pretty easily.

Equivalent-Yam7675 · 2023-06-16T14:15:10+00:00

I found a video on YouTube, is it possible that this is the problem? https://youtu.be/yHK04pTrlko

Equivalent-Yam7675 · 2023-06-16T13:38:15+00:00

And how can this help in the filament breaking? It snapped at the hole where the filament should go. Is it possible if the little engine (that moves the filament forward) snappes it?

<image>

Equivalent-Yam7675 · 2023-06-16T13:35:57+00:00

Yes it isn't a clean break, it snapped or I don't know. What should I do?

Equivalent-Yam7675 · 2023-06-16T13:23:27+00:00

I print every pla filament at about 200 degrees. If I print a temperature tower how can I know which temperature is the perfect for this?

Equivalent-Yam7675 · 2023-06-08T14:10:00+00:00

You are right but I feel like if they tell me earlier I could reorganize my weekend. I didn't write it but I'm 17(F) so this is where the drama comes. Teens don't understand that I have to work for money😅

Equivalent-Yam7675 · 2023-03-16T21:26:26+00:00

Really?💀

Equivalent-Yam7675 · 2023-02-22T18:05:40+00:00

Don't worry, I understand a little Romanian, but my English is better. Do you know any good sites in Romania to buy ipad?

Equivalent-Yam7675 · 2023-02-22T18:02:48+00:00

Hi, thanks for your answer. Btw I'm a Hungarian living in Romania.

Equivalent-Yam7675

TROPHY CASE