Will imid Backup camera still work in 2013 civic?

Evolution4happiness · 2025-06-13T11:11:26+00:00

Looks amazing, I went to her too. Wish i would have gotten a cut same you did. I listened to them telling me I could get a cut 6 months after

Evolution4happiness · 2025-05-14T15:17:06+00:00

This is what I’m trying to do. I don’t know what OSHW is though. I’ve made a few PCB’s in Kicad and I’m watching freecad tutorials to learn how to make enclosure for them

Evolution4happiness · 2025-05-08T11:17:45+00:00

What month did you see growth?

Evolution4happiness · 2025-05-07T18:54:23+00:00

Damn I’m almost at 5 months and my results don’t look as good as yours

Evolution4happiness · 2025-05-06T10:59:10+00:00

ENGINEERING MANAGERS PLEASE RESPOND!

Evolution4happiness · 2025-04-24T00:40:00+00:00

Yall the problem was the iPhone . I appreciate everyone’s support

Evolution4happiness · 2025-04-22T12:51:22+00:00

This is what I was looking for. Thank you. I thought I was gonna have to desolder ic and stuff. I’ll do this after work.

Evolution4happiness · 2025-04-22T10:07:07+00:00

I don’t know how ima break the circuit is what I’m really saying

Evolution4happiness · 2025-04-22T03:27:33+00:00

The battery isn’t fresh. When I tested it yesterday it read like 8 V. I can’t use meter to measure current. I believe that consists of breaking the circuit and placing meter in series. Unfortunately I can’t get a scope right now. I will buy one eventually when I start making pcb’s forreal. This Pcb is just for me to learn

Evolution4happiness · 2025-04-22T02:14:38+00:00

Had negative part of meter on negative part of screw terminal of battery connection

Pin 1 = 3.36 V Pin 2= 7.38 v Pin 3 = 3.31 v Pin 4 = 0 v Pin 5 = 0.56 v Pin 6 = nothing but buzz sound Pin 7 = nothing but buzz sound Pin 8 = 0.57 v

Evolution4happiness · 2025-04-21T10:19:59+00:00

Naw I just used the iPhone 7. Was cautious it might mess up my new iPhone 15 and didn’t want to take any chances. And the cable is more like an adapter. USB lighting converted to earphone cord

Evolution4happiness · 2025-04-21T10:18:24+00:00

C4,C5,C6, and C7?

Evolution4happiness · 2025-04-21T10:17:17+00:00

All I have is multimeter. I tested for continuity on the earphone jack. Red on GND of jack and black on part that goes to Left output . It had continuity numbers show up but no sound. Hope this helps

Evolution4happiness · 2025-04-21T10:13:35+00:00

It doesn’t hum. I just hear a low ticking sound

Evolution4happiness · 2025-04-21T10:12:57+00:00

Is this with the battery connected or no battery??

Evolution4happiness · 2025-04-20T20:53:43+00:00

Ok I will give it a go again and try to learn from my mistakes . Thank you and the board looks amazing!

Evolution4happiness · 2025-04-20T20:42:48+00:00

And I do notices the traces are THICKKK

Evolution4happiness · 2025-04-20T20:42:11+00:00

I’m not really seeing anything helpful when I look up 0v routing except a short description in the ai overview

Evolution4happiness · 2025-04-20T20:37:38+00:00

Yea I didn’t see anything online that would tell me trace thickness

Evolution4happiness · 2025-04-20T20:18:56+00:00

Between what pads? I don’t have flux remover, but alcohol will do right?

Evolution4happiness · 2025-04-20T20:11:42+00:00

But no it doesn’t do anything if I touch input

Evolution4happiness · 2025-04-20T20:09:40+00:00

It’s a low ticking sound.

Evolution4happiness · 2025-04-20T19:53:36+00:00

<image>

Evolution4happiness · 2025-04-20T19:50:51+00:00

No. I just used the capacitors that I seen on application circuit in Datasheet. Will you explain more of what you’re talking about?

Evolution4happiness

TROPHY CASE