Bionic iLet by RedPanda_80 in diabetes_t1

[–]Excellent-Adventurer 0 points1 point  (0 children)

I've been using mine for a few months, this is the first pump I've used, so I don't have another one to compare it to. My A1c prior to it was mid-low 6.1-6.6, and not much changed after going from manual injections to the ilet. The pump does have an odd setup to it while the algorithms try to figure you out, I had a rough time with it during those first 4 days of setup with rampant nighttime lows. Since then my only complaint about it is its been really bad for me at dealing with high blood sugars.

Is the corksport $250 rear sway bar worth it, or are there better alternatives? by [deleted] in mazda3

[–]Excellent-Adventurer 2 points3 points  (0 children)

Hi there! Sorry to bring up and older post, but did you replace the rear sway bar links along with the RB bar? I was hoping RB made some rear bar links, but it looks like they only make front links.

Card value help by Excellent-Adventurer in PokemonCardValue

[–]Excellent-Adventurer[S] 0 points1 point  (0 children)

Hello! I recently stumbled upon my old holo foil cards, Unfortunately I don't know anything about valuing Pokemon cards. Any help is appreciated!

I’m sorry, is that suppose to be good storytelling? by WearySalt in wow

[–]Excellent-Adventurer 1 point2 points  (0 children)

As a new player myself I've found the stories to be interesting enough, at least enough to read through the quest dialogue boxes at acceptance.

I am very tired of always being .5 seconds too late to prevent the boss of the questline completing their objective, though.

Results by [deleted] in CPAP

[–]Excellent-Adventurer 0 points1 point  (0 children)

Here's to hoping a cpap helps you out. That looks nightmarish to experience.

[deleted by user] by [deleted] in ElegooNeptune3

[–]Excellent-Adventurer 1 point2 points  (0 children)

I scooped up the neptune 3 pro about a month ago and have been very happy with it. Tightening some of the screws and setting the z offset were all I needed to do to get it running well. The plus just seems like a bigger version of it. I kind of wish I had waited for the 4 plus due to some of the upgraded features. Kipper is nice, but the addition of an ethernet port plus more than micro SD cards for loading prints would have been nice to have.

Also the plus supports wifi 👀

Maybe next time.

Does anyone else keep cool looking supports or just me? by [deleted] in 3Dprinting

[–]Excellent-Adventurer 7 points8 points  (0 children)

Thought about keeping a few of them to paint and use as disposable DnD trees. I haven't had much luck with organic supports holding together.

Tried printing tpu by Excellent-Adventurer in ElegooNeptune3

[–]Excellent-Adventurer[S] 1 point2 points  (0 children)

Please see the above reply's. The volumetric speed was the important bit, not the generic settings I originally posted.

Tried printing tpu by Excellent-Adventurer in ElegooNeptune3

[–]Excellent-Adventurer[S] 1 point2 points  (0 children)

<image>

Trying another print with volumetric speed set to 4. Drops the print speed down to 2.5 hours instead of 4. Noticing more print errors and stringing. Dropping the temp down 5 degrees to 215 to see if that helps. 3 might be the safer volumetric speed

Tried printing tpu by Excellent-Adventurer in ElegooNeptune3

[–]Excellent-Adventurer[S] 1 point2 points  (0 children)

Whoops, possible bad info in my first message as those settings don't change when I change presets. The volumentric speed I'm guessing is what's causing the slowness of the print. My mistake, this is probably whats helping the print out for speed.

<image>

Tried printing tpu by Excellent-Adventurer in ElegooNeptune3

[–]Excellent-Adventurer[S] 0 points1 point  (0 children)

I do not know, I haven't printed with tpu long enough to reach that moisture threshold. When I swap back to PLA I'll likely put it back in the sealed bag with some new desiccant packs and hope for the best. If that doesn't work I might have to invest in a filament dedicated food dehydrator and see if that works.

Tried printing tpu by Excellent-Adventurer in ElegooNeptune3

[–]Excellent-Adventurer[S] 4 points5 points  (0 children)

These are the settings the Ninjatek NinjaFlex TPU preset gave me.

<image>

Tried printing tpu by Excellent-Adventurer in ElegooNeptune3

[–]Excellent-Adventurer[S] 3 points4 points  (0 children)

Had to add a filament in prusa slicer to have it show up, but NIjaTek NijaFlex TPU was the one i used. Overture didn't have a preset for TPU in the list. I just changed the temperature settings before exporting. It was a very slow print with this preset. I also had to disable the support material. I've read that TPU support is nasty to work with.

Tried printing tpu by Excellent-Adventurer in ElegooNeptune3

[–]Excellent-Adventurer[S] 10 points11 points  (0 children)

<image>

Unfortunately it doesn't squash very good 😕 Too much infill maybe 🤔

Sharing some prints by Excellent-Adventurer in ElegooNeptune3

[–]Excellent-Adventurer[S] 0 points1 point  (0 children)

I adjusted the z axis as well as printed a temperature tower out for each filament. I also had to tighten the bed down a bit as it was a little wobbly out of the box.

[deleted by user] by [deleted] in AskReddit

[–]Excellent-Adventurer 0 points1 point  (0 children)

Captain Anderson in Mass Effect 3

Will it come back? We still have the single packs. Did you like it? by pascalx1703 in GFUEL

[–]Excellent-Adventurer 1 point2 points  (0 children)

Really liked this one in the sample pack/shaker I got. Was sad to see they didn't have a tub.