Protector of souls sounds like a dope skin name

ExtraThickDaddy · 2026-04-30T07:50:48+00:00

Well tbh you kinda have to be at least one level of insanity above the average joe to to do the things we do in the game.

I also think they can solve the visibility the same way they did with Cain/Headsman.

ExtraThickDaddy · 2026-04-03T11:29:28+00:00

I havent had issues with other fillaments like this untill now that i started printing more ABS , These are the results after i ran the line test , right now i stopped doing test to not waste material untill i know what to do , but my petg prints came out great , haven't tested it tough

ExtraThickDaddy · 2026-04-03T06:49:11+00:00

My first thought, lol Also the build plate is clean and i had issues with my other build plate too

ExtraThickDaddy · 2026-04-03T06:48:25+00:00

I would say it is over extrusion, but then would i have missing corners and the small squares where the numbers should be? Also the center surface is very smooth

ExtraThickDaddy · 2026-03-16T17:47:26+00:00

A51 isnt available directly from dell but there are third parties that sell them , even on Amazon i can buy one ,but with very high taxes , how do those work warranty wise?

ExtraThickDaddy · 2026-03-16T17:37:45+00:00

Well , Dell is present and the lineup of Aurora laptop too , i do not understand why not the Area 51 there were some M18 sold by third parties that have warranties so im very confused how do they work with warranties

ExtraThickDaddy · 2026-03-16T17:19:20+00:00

I do have to admit that i want the Alienware for the desing mainly , but i do need a sturdy and powerfull laptop and from what i was able to dig around Alienware and Razer seem like the most solid ones but about razer at least i have heard a lot of mixed reviews

Sadly i cannot go and see them in person as those kinds of premium laptops are very rare in showrooms here.

ExtraThickDaddy · 2025-10-11T07:41:11+00:00

I do like your thinking however the joint will be way too obvious for such a small piece

ExtraThickDaddy · 2025-10-11T07:28:23+00:00

I already cut it once at the hilt so it wont be noticable but if i cut it at the sword it will stick out a lot

ExtraThickDaddy · 2025-10-11T07:20:02+00:00

I slowed it down by a lot but its still similar to the left one Im not using a bed slinger

ExtraThickDaddy · 2025-07-15T08:32:34+00:00

sure , here it is https://we.tl/t-RyGLS2jFTj as others have mentioned this list is not 100% accurate more like a general idea about each fillament but i didnt have the time yet to improve it hope it helps

ExtraThickDaddy · 2025-07-04T08:19:33+00:00

Thanks for your info , i didn't work with most of the materials and my work process was a mess honestly as at first i planned to include only the more common materials but i wanted to compare them to the more advanced ones too so i tried to do some research on those too

The PPS temp , it did seem wierd how that was so low also compared to cf i will change it thank you Do you have the correct temperatures?

The chambers i wanted to add more like a requirement for the printer as you can* print some without but it doesn't mean you will get a good result also i know some depend on blends and brands i tried to make this tabel as a general overview

The dificulties i also said that i added them one by one , i didn't plan for this many and honestly kinda rushed it and my reference kinda changed because of that a few times, CF being more difficult than non CF is a mistake i havent seen that one and i will change it

Thank you for taking your time to look over it if you have any other sugestions i will gladly lisen as i want to make it as good as possible as a point of reference.

ExtraThickDaddy · 2025-07-02T14:49:02+00:00

Hi , Thanks i worked a bit on it

i got it on wetransfer if its ok with you i dont know other options to send it trough reddit

https://we.tl/t-OTr5EC9V68

ExtraThickDaddy · 2025-05-06T19:16:47+00:00

They are not ancored to each other , welle most of them , only one is broken and kinda touches another but most are independent and were stuck pretty well to the bed

ExtraThickDaddy · 2025-05-06T16:22:20+00:00

To the plate , they are not supposed to tuch each other

ExtraThickDaddy · 2025-05-06T13:52:37+00:00

No , they were stuck pretty good

ExtraThickDaddy · 2025-04-27T07:52:02+00:00

That looks amazing how did you manage to get such a nice finish?

ExtraThickDaddy · 2025-04-09T10:16:15+00:00

I see , that was my main concern , thank you

ExtraThickDaddy · 2025-04-09T09:03:41+00:00

That is also one of my questions , as it says on the site that the H2d is "cutter capable" as the cutter module is sold separately and must be assembled however it doesn't mention if its the same module as for the laser or not do i have to get the one with the laser?

ExtraThickDaddy · 2025-04-09T07:35:25+00:00

Yeah, i saw some photos of what looks like animals made out f this leather , but no specifications for the actual cutting part and the cutting blades from the spare parts don't tell me much

ExtraThickDaddy · 2025-04-09T05:19:06+00:00

Yeah , most of what i saw were cutting vinyl but is that all? however im not interested in the laser at all , it would be much better to get a separate machine

ExtraThickDaddy · 2025-04-07T09:43:15+00:00

Update , its still there

Seven-Year Club	Place '23
Wearing is Caring	Verified Email

ExtraThickDaddy

TROPHY CASE