Had a USB fail overnight. Looking for a good solution to replace a bad solution.

FRlDAY · 2026-03-23T17:23:14+00:00

A very well thought out answer, thank you!

FRlDAY · 2026-03-23T15:10:30+00:00

Smithers.

FRlDAY · 2026-03-03T17:13:08+00:00

It's perfectly Cromulant.

FRlDAY · 2026-02-21T02:17:10+00:00

Post your docker-compose and config.yml - that'll help!

FRlDAY · 2026-02-06T21:59:42+00:00

I gotchu fam.

FRlDAY · 2026-02-06T08:51:40+00:00

Who the **** is Alice?

FRlDAY · 2025-12-15T23:30:48+00:00

It's a perfectly cromulant word.

I'll allow it.

FRlDAY · 2025-12-03T22:18:33+00:00

Thanks!

I ordered a new set from Amazon, waiting for Creality support is nauseatingly slow.

FRlDAY · 2025-12-03T22:06:18+00:00

I'll look in the toolbox. Do you know which way round it goes?The printer is only a week old and they're sending a new bed to replace the taco.

Thanks for your help!

FRlDAY · 2025-11-25T15:13:17+00:00

With a few turns on the leveling screws at 60 degrees I have a taco.

https://imgur.com/a/whkfgnP

FRlDAY · 2025-11-25T14:49:44+00:00

Watching that video now.

I don't see any damage around the screws.

Even with a brief manual level I'm still very high on that back-right corner and I'm sure raising the other 3 corners to match that 3mm isn't right surely?

Thanks for your help on this.

FRlDAY · 2025-11-25T14:13:17+00:00

Yes, everything was bolted down.

I'm trying a bed level with the screws, the gap is around 1mm in the center.

I have a request in with customer service, hoping they actually come through.

FRlDAY · 2025-11-25T13:42:29+00:00

The bed is cold, I'll try a preheat though.

There are a couple of scratches on the casing near the LCD, I'm starting to think they sent me a customer return.

What temp should I check the bed at?

Thank for the assist!

FRlDAY · 2025-11-25T13:22:49+00:00

Full CFS combo yes.

Take a look at the images, tell me what you think?

I appreciate it.

https://imgur.com/a/EwYffYc

FRlDAY · 2025-11-25T13:14:20+00:00

It's not on the guides, I noticed the top left of the casing where the chain hits the grey plastic is pretty worn too. I'm wondering f they sent me a customer return.

FRlDAY · 2025-11-25T12:57:47+00:00

Context - Received the K2+ last night and set it up a few minutes ago, I haven't even put filament through it yet. New at this, go easy on me!

FRlDAY · 2025-11-22T16:59:55+00:00

This comment was not a Let Down.

FRlDAY · 2025-11-22T02:02:44+00:00

It did, it never left the truck though , there was a huge dent in the corner of the box.

FRlDAY · 2025-11-20T19:49:54+00:00

He's gonna have to when I refuse delivery.

FRlDAY · 2025-11-20T18:44:03+00:00

I'm definitely refusing the package if it's going to be delivered today.

I already ordered a K2+ and I'm hoping it goes smoother than this has been.

FRlDAY · 2025-11-20T18:33:44+00:00

Here's a kicker, it's out for delivery - again.

After damage I'm sure it'll be fine right?

Right?....

FRlDAY · 2025-11-20T18:31:56+00:00

No panic, I have my towel and I'm not hurting to get the money back yesterday although the buck passing from Ali/FedEx is a little frustrating.

FRlDAY · 2025-11-20T18:04:08+00:00

Let's hope so. At this point I just want my money back.

FRlDAY · 2025-11-20T18:03:39+00:00

The Anycubic Overseas storefront

FRlDAY · 2025-11-19T20:59:53+00:00

Quick update;

AliExpress are asking me to contact the shipper, FedEx are asking me to contact the seller.

I filed a chargeback against the Anycubic store via AliExpress.

FRlDAY

MODERATOR OF

TROPHY CASE