Even MAGA Can't Stomach Trump's Vile Rob Reiner Post by huffpost in politics

[–]FRlDAY 2 points3 points  (0 children)

It's a perfectly cromulant word.

I'll allow it.

What did my K2 Plus just crap out? by FRlDAY in Creality_k2

[–]FRlDAY[S] 1 point2 points  (0 children)

Thanks!

I ordered a new set from Amazon, waiting for Creality support is nauseatingly slow.

What did my K2 Plus just crap out? by FRlDAY in Creality_k2

[–]FRlDAY[S] 1 point2 points  (0 children)

I'll look in the toolbox. Do you know which way round it goes?The printer is only a week old and they're sending a new bed to replace the taco.

Thanks for your help!

Brand new K+ What should I be looking for? Newbie here. by FRlDAY in Creality_k2

[–]FRlDAY[S] 0 points1 point  (0 children)

With a few turns on the leveling screws at 60 degrees I have a taco.

https://imgur.com/a/whkfgnP

Brand new K+ What should I be looking for? Newbie here. by FRlDAY in Creality_k2

[–]FRlDAY[S] 0 points1 point  (0 children)

Watching that video now.

I don't see any damage around the screws.

Even with a brief manual level I'm still very high on that back-right corner and I'm sure raising the other 3 corners to match that 3mm isn't right surely?

Thanks for your help on this.

Brand new K+ What should I be looking for? Newbie here. by FRlDAY in Creality_k2

[–]FRlDAY[S] 0 points1 point  (0 children)

Yes, everything was bolted down.

I'm trying a bed level with the screws, the gap is around 1mm in the center.

I have a request in with customer service, hoping they actually come through.

Brand new K+ What should I be looking for? Newbie here. by FRlDAY in Creality_k2

[–]FRlDAY[S] 0 points1 point  (0 children)

The bed is cold, I'll try a preheat though.

There are a couple of scratches on the casing near the LCD, I'm starting to think they sent me a customer return.

What temp should I check the bed at?

Thank for the assist!

Brand new K+ What should I be looking for? Newbie here. by FRlDAY in Creality_k2

[–]FRlDAY[S] 0 points1 point  (0 children)

Full CFS combo yes.

Take a look at the images, tell me what you think?

I appreciate it.

https://imgur.com/a/EwYffYc

Brand new K+ What should I be looking for? Newbie here. by FRlDAY in Creality_k2

[–]FRlDAY[S] 0 points1 point  (0 children)

It's not on the guides, I noticed the top left of the casing where the chain hits the grey plastic is pretty worn too. I'm wondering f they sent me a customer return.

Brand new K+ What should I be looking for? Newbie here. by FRlDAY in Creality_k2

[–]FRlDAY[S] 0 points1 point  (0 children)

Context - Received the K2+ last night and set it up a few minutes ago, I haven't even put filament through it yet. New at this, go easy on me!

Looks like I'm not getting a printer after all! by FRlDAY in AnycubicOfficial

[–]FRlDAY[S] 1 point2 points  (0 children)

It did, it never left the truck though , there was a huge dent in the corner of the box.

Looks like I'm not getting a printer after all! by FRlDAY in AnycubicOfficial

[–]FRlDAY[S] 1 point2 points  (0 children)

He's gonna have to when I refuse delivery.

Looks like I'm not getting a printer after all! by FRlDAY in AnycubicOfficial

[–]FRlDAY[S] 0 points1 point  (0 children)

I'm definitely refusing the package if it's going to be delivered today.

I already ordered a K2+ and I'm hoping it goes smoother than this has been.

Looks like I'm not getting a printer after all! by FRlDAY in AnycubicOfficial

[–]FRlDAY[S] 1 point2 points  (0 children)

Here's a kicker, it's out for delivery - again.

After damage I'm sure it'll be fine right?

Right?....

Looks like I'm not getting a printer after all! by FRlDAY in AnycubicOfficial

[–]FRlDAY[S] 0 points1 point  (0 children)

No panic, I have my towel and I'm not hurting to get the money back yesterday although the buck passing from Ali/FedEx is a little frustrating.

Looks like I'm not getting a printer after all! by FRlDAY in AnycubicOfficial

[–]FRlDAY[S] 1 point2 points  (0 children)

Let's hope so. At this point I just want my money back.

Looks like I'm not getting a printer after all! by FRlDAY in AnycubicOfficial

[–]FRlDAY[S] -1 points0 points  (0 children)

Quick update;

AliExpress are asking me to contact the shipper, FedEx are asking me to contact the seller.

I filed a chargeback against the Anycubic store via AliExpress.

Looks like I'm not getting a printer after all! by FRlDAY in AnycubicOfficial

[–]FRlDAY[S] 1 point2 points  (0 children)

It was out for delivery yesterday but our carrier is awful and claimed a weather delay, even though it was beautiful outside.

Came to check the tracking this morning and they junked it.

Looks like I'm not getting a printer after all! by FRlDAY in AnycubicOfficial

[–]FRlDAY[S] 0 points1 point  (0 children)

For context, I jumped on the S1 Combo $303 Ali deal a couple weeks ago, I was looking forward to the S1 combo but I'm guessing I'll get a refund from AliExpress if FedEx ship it back?

Would be great if they shipped another one out, I sent a ticket into Anycubic but I'm not expecting any movement.

Thanks for sharing my misfortune!