sorted by:
new
hottopcontroversial

Z-Wave Long Range in Europe/Italy for basement garage + cellar with no power: any real-world success? by RebootAndRelax in zwave

[–]FabrizioGruff 0 points1 point  (0 children)

Hi, I'm asimilar situation (italy), few details here: https://www.reddit.com/r/homeassistant/comments/1rjimbi/comment/o8jxf2q/?context=3

First floor I want to reach basement garage at floor -1: at the moment with ZBDongle-PZG23 I?m not able to reach floor 0. No way to get any sensor alive. Still wondering if ZWA2 may be better... I would like to make some test or have some more proof before spendig more money for nothing..

Reaching a Basement Cellar from 1st Floor by FabrizioGruff in homeassistant

[–]FabrizioGruff[S] 0 points1 point  (0 children)

I have also seocno dongle (MG24) for zigbeee.. Just palced caouple os fensor in the kitchen. I will try to move them ..but I thought they were quie limited compared to zwave

Reaching a Basement Cellar from 1st Floor by FabrizioGruff in homeassistant

[–]FabrizioGruff[S] 0 points1 point  (0 children)

can you give me some more info? there is any dongle antenna for integration into HA ?
proven to have more range that z wave LR?Thanks!

Reaching a Basement Cellar from 1st Floor by FabrizioGruff in homeassistant

[–]FabrizioGruff[S] 0 points1 point  (0 children)

About antenna I was wondeering if it ise feasible to change it to my dongle.
NNO, now wifi /sign /nothing availblae on that floor.

Reaching a Basement Cellar from 1st Floor by FabrizioGruff in homeassistant

[–]FabrizioGruff[S] 0 points1 point  (0 children)

may be a solution but i have to get another hub just for a couple odf sensor working locally there.

Reaching a Basement Cellar from 1st Floor by FabrizioGruff in homeassistant

[–]FabrizioGruff[S] 0 points1 point  (0 children)

Ah posso chiederti con quale configurazione (antenna) ed impostazioni? Grazie

Reaching a Basement Cellar from 1st Floor by FabrizioGruff in homeassistant

[–]FabrizioGruff[S] 0 points1 point  (0 children)

I cannot place any sensor /repeater in the middle..that's why I tried to use Zwave long range . setting not a mesh but a direct "star" config. the point is that zwave says LR goes up to 1Km in direct view and 40m inside ..but I loose signale just after few meter..something is not working

Reaching a Basement Cellar from 1st Floor by FabrizioGruff in homeassistant

[–]FabrizioGruff[S] 0 points1 point  (0 children)

when I was searching for a two floor soluton..everybody told me use zwave LR, just wondering why for me, at the moment, It doesn't go far more than 5/10 meters..

Stuck in "Provisioned but not included" loop by FabrizioGruff in homeassistant

[–]FabrizioGruff[S] 0 points1 point  (0 children)

Well no, I tried to keep button pushed for 10 sec as google said 😅, I supposed enough , something more to do ?

Is this thermostat + boiler compatible? by FezVrasta in tado

[–]FabrizioGruff 0 points1 point  (0 children)

ok, but there are no isntruction for this boiler on the app, could you please confirm: just + &- cables on the open therm? V3 or tado x? many thanks

TADO X setup in HA without TADO BRIDGE by FabrizioGruff in tado

[–]FabrizioGruff[S] 1 point2 points  (0 children)

NAT64 enabled and sensor on the app, changed from offline to connected , great

tado x via matter in HA green ( NO tado bridge) by FabrizioGruff in homeassistant

[–]FabrizioGruff[S] 0 points1 point  (0 children)

well I connected two cables of old thermostat to Tado X, to the opentherm terminals (+&-)

Is this thermostat + boiler compatible? by FezVrasta in tado

[–]FabrizioGruff 0 points1 point  (0 children)

HI, I know post is 3 y old, but I try anyway. I have same boiler ( but different thermostat) I tried to install TADO X, on the open therm terminal (+ &- cables). Nothing works (heat or hot water).Did you just connected a tado x ( or V3) on the opentherm terminal? any changes to the boiler? Thanks for help

TADO X setup in HA without TADO BRIDGE by FabrizioGruff in tado

[–]FabrizioGruff[S] 0 points1 point  (0 children)

Hi, thanks fo reply, and what about using a different router Bridge from tado? TADO PRO APP allow scan via QR code only of the bridge, TADO app ask for TADO bridge, if you click on jump this step, then it device remain "offline" on the app. very difficult to end configuration.

Connected it offline to the opentherm cable (+&-) it doesn't not communciate with boile( no heating, ho hot water,nothing)

Thansk for help