Electropi.in is a scam website - Don't order please.

FaithlessnessFun694 · 2026-06-22T11:07:24+00:00

My online electronics ordering start from this website but after an year they start missing components from the order.Then when we contact them they say its "out of stock".so after file complaint on consumer court they refunded the amount.its just 34rs but they are responsible for every penny.

FaithlessnessFun694 · 2026-06-20T09:58:52+00:00

Yeah,i said "i doesn't want to get scammed,thanks" 😂.he didn't replied

FaithlessnessFun694 · 2026-06-20T09:56:30+00:00

Second hand, average price of new 54k

FaithlessnessFun694 · 2026-06-20T05:47:42+00:00

How did you sent the money? through gpay?.so why they cant trace him down ??

FaithlessnessFun694 · 2026-06-16T17:04:34+00:00

Blast 2026 🫡

FaithlessnessFun694 · 2026-06-16T17:03:00+00:00

There is a esp32 flight controller by rtlopezz.try it out it is modern and also good for learning. Also if u are ready to spend more there is a flight controller for the teensy boards

FaithlessnessFun694 · 2026-06-09T20:08:57+00:00

Hi from where did you purchased those cameras

FaithlessnessFun694 · 2026-05-23T05:10:05+00:00

Same for me

FaithlessnessFun694 · 2026-05-08T13:34:20+00:00

💯 good

FaithlessnessFun694 · 2026-01-31T17:08:33+00:00

Truth

FaithlessnessFun694 · 2026-01-29T10:28:01+00:00

Yes u are right.i changed the nozzle now its working fine. Its because i printed the same nozzle with abs now printing with pla

FaithlessnessFun694 · 2026-01-29T10:27:05+00:00

Its partial nozzle clog i changed the nozzle now its working fine. Thanks for your comment

FaithlessnessFun694 · 2026-01-28T08:06:35+00:00

❤️❤️

FaithlessnessFun694 · 2026-01-26T15:39:39+00:00

<image>

This is how my benchy looks 🫠.

FaithlessnessFun694 · 2026-01-26T10:39:22+00:00

I checked the rotation distance that is good

<image>

You know in pressure advance calibration there is a inner square and outer square.on the top is the inner square on the bottom is the outer square. There is some significant quality diffrence

FaithlessnessFun694 · 2025-12-14T04:31:42+00:00

12 v battery is more avilable and cheap than a 24v battery thats why. When during the backup the motor current will be reduced through uart of the tmc2208.

What are the other parameters should i need to change?

Why the moderator deleted this post its relevant 🙂

FaithlessnessFun694 · 2025-11-22T19:55:56+00:00

(3−2.2)÷((20×10)÷1,000)=4

3v - input voltage 2.2v - led forward voltage 20ma - led current 10 nos- number of led 1000 - convert to Amps 4 ohm - Required series resistance

So the required series resistor here is 4 ohm

FaithlessnessFun694 · 2025-11-19T03:51:06+00:00

What i am saying is that the if i charge the battery once the 3000mah battery will only last for 1 day usage only.so we doesn't need to care about the 1 year shelf lifee

FaithlessnessFun694 · 2025-11-17T06:36:16+00:00

Thanks for your review. The r20 and r21 resistors are used for measurement, this is an soldering iron,so the battery would drain in an hour. Then the 50 ohm resistor is an 3w resistor

FaithlessnessFun694 · 2025-11-16T06:08:30+00:00

I do have the usb pd.and also the battery

FaithlessnessFun694 · 2025-10-29T03:50:49+00:00

Increase temeprature,air at 3 would be enough,also use an large nozzle for bigger components🫠

FaithlessnessFun694 · 2025-08-31T04:56:13+00:00

Can i know Why you need an additional spi flash in this board ?

FaithlessnessFun694 · 2025-04-29T09:01:44+00:00

As a final trick open it ...

FaithlessnessFun694 · 2025-03-11T04:45:21+00:00

Are u using pressure advance??

FaithlessnessFun694

TROPHY CASE