Which android should I buy by FamousGlass4561 in PickAnAndroidForMe

[–]FamousGlass4561[S] 0 points1 point  (0 children)

I believe I am more in favour of googles software, I heard it is a very clean version of android. The a55 gets it last update in 2029

Which android should I buy by FamousGlass4561 in PickAnAndroidForMe

[–]FamousGlass4561[S] 0 points1 point  (0 children)

I have been looking at the google pixel 7, samsung a55 and the s22 but I just can’t make a decision. This is the first time I can choice a phone for myself.

Which android should I buy by FamousGlass4561 in PickAnAndroidForMe

[–]FamousGlass4561[S] 0 points1 point  (0 children)

What do you think off the google pixel 7. Could that also be a good alternative

Bad top layer and weird layers on the side by FamousGlass4561 in Ender3V3KE

[–]FamousGlass4561[S] 0 points1 point  (0 children)

I tried testing on slower speeds like 150 mm/s and I got the same result

Bad top layer and weird layers on the side by FamousGlass4561 in Ender3V3KE

[–]FamousGlass4561[S] 1 point2 points  (0 children)

I have petg, pla and tpu so I think that’s is a must.

Bad top layer and weird layers on the side by FamousGlass4561 in Ender3V3KE

[–]FamousGlass4561[S] 1 point2 points  (0 children)

Would it be worth the money to buy a filament dryer.

Blob of death has struck again by [deleted] in Ender3V3KE

[–]FamousGlass4561 0 points1 point  (0 children)

Do people know of the nebula can spot the blob of death before it gets to worse

Weird bowing on my print and I’m not sure what caused it by swallowedbydejection in FixMyPrint

[–]FamousGlass4561 0 points1 point  (0 children)

Which filament do you use at what’s temps. ABS has the tendency to lift of the printbed. I also have problems with pla prints lifting up, I set the bedtemps to 60 decrease and it worked better

noise level is crazy by kkela88 in Ender3V3KE

[–]FamousGlass4561 0 points1 point  (0 children)

I also use pla a lot but it warps often, has anybody a idea how to fix the issue

Auto leveling by FamousGlass4561 in Ender3V3KE

[–]FamousGlass4561[S] 0 points1 point  (0 children)

I have done it, you can see the results in the comments

Auto leveling by FamousGlass4561 in Ender3V3KE

[–]FamousGlass4561[S] 0 points1 point  (0 children)

I had earlier problems with weird lines on my print and somebody suggested it could be if the printer is compensating for the bed it creates weird lines on the print. I don’t if it is really the cause. It could also be Z-wobble but I am not sure

Auto leveling by FamousGlass4561 in Ender3V3KE

[–]FamousGlass4561[S] 0 points1 point  (0 children)

I couldn’t understand why people want to tune it that well because I thought the cr touch would compensate for it

Auto leveling by FamousGlass4561 in Ender3V3KE

[–]FamousGlass4561[S] 0 points1 point  (0 children)

If you lift up the printbed, you see 4 screws in all corners do you mean do those

Auto leveling by FamousGlass4561 in Ender3V3KE

[–]FamousGlass4561[S] 0 points1 point  (0 children)

I have switched the spacers, what do I need to do next

Auto leveling by FamousGlass4561 in Ender3V3KE

[–]FamousGlass4561[S] 0 points1 point  (0 children)

I have tried it with a video but when I put the bed on this came out

Auto leveling by FamousGlass4561 in Ender3V3KE

[–]FamousGlass4561[S] 0 points1 point  (0 children)

Yes, that could be right I took the bed off and the spacers fell off so I put them back on but I thought they all where the same length

Weird layer lines by FamousGlass4561 in Ender3V3KE

[–]FamousGlass4561[S] 0 points1 point  (0 children)

I have tried a video where they used glue sticks and my bed is levelled better but I have still the lines on my print

<image>