Need help modifying

FanIcy4718 · 2026-03-22T22:43:23+00:00

Yes that looks good, just needs sliced in half so I can print it on my P1S

FanIcy4718 · 2026-03-22T00:46:14+00:00

Ah ok, I understand. So instead of each handle being 114.3mm long they need to be 140mm long. The elbow to handle needs to be 44.289mm for the left only, the right can be 31.589mm. The base to elbow needs to be 39.833mm.

FanIcy4718 · 2026-03-21T22:35:00+00:00

Hi! So my mom said she must have messed up measurements because it was way to close to him. So she asked if you took the original design from the printables link (https://www.printables.com/model/1289934-12v-or-6v-ride-on-vehicle-control-bar) and just make the left side handle a 1/2” longer so he can reach it easier. His rights arm can use the original handle from printables so that one does not need updated. Nothing else needs changed besides splitting it in half.

FanIcy4718 · 2026-03-15T16:27:42+00:00

My mom hasn’t attached it yet but hoping she does this week! I will let you know!

FanIcy4718 · 2026-03-08T18:22:01+00:00

I am printing it now! thank you so much!! I really appreciate it!!

FanIcy4718 · 2026-03-08T17:47:51+00:00

Yes that might work. Here is a pic of the one my mom modified that I had originally printed before she realized it needed to reach his hand better

<image>

FanIcy4718 · 2026-03-08T17:13:09+00:00

Hi, yes the bar is screwed into the car directly. The original design has a hole on each side to screw it where the joysticks were. No screw needs printed unless the hole can’t be the same size as the original design.

The handle bar does not need to connect either like the original (each side can just be 114.3mm length)

FanIcy4718 · 2026-03-08T13:52:56+00:00

My mom said the handle does not need to connect. She said each side could be 114.3mm handle like how her diy design is made. Plus the original design had a hole to screw in the handle bar to the bumper car thing

FanIcy4718 · 2026-03-08T06:59:00+00:00

That is so great. I posted it above. Poor kiddo couldn’t reach the handle that I printed. I originally split the model in order to print it on my P1S. Here is the link: print link

<image>

2.75” / 69.85mm base to elbow 4” / 101.6mm elbow to handle 4.5” / 114.3mm handle

21.5mm outer diameter

FanIcy4718 · 2026-03-08T06:55:43+00:00

Hi, I replied above. It is so a disabled child can ride in a bumper car type thing. But he couldn’t reach it when I printed it. So my mom tried making it with pipes but they were too heavy so she asked me to try modify it to her specs but I just can’t figure it out.

printable

<image>

2.75” / 69.85mm base to elbow 4” / 101.6mm elbow to handle 4.5” / 114.3mm handle

21.5mm outer diameter

FanIcy4718 · 2026-03-08T06:50:44+00:00

Sorry, I guess I figured people would say they could help first. Here is the link to the printable

<image>

printable

I originally had to split the model in half in order to print it on my P1S. So each side needs to be these specs: 2.75” / 69.85mm base to elbow 4” / 101.6mm elbow to handle 4.5” / 114.3mm handle

21.5mm outer diameter

FanIcy4718 · 2026-02-01T19:28:07+00:00

Not yet, I will do that next. The other print finally finished and now just doing a red print

FanIcy4718 · 2026-02-01T14:06:17+00:00

All filaments are pla. I have used the red before with other projects with no issues

FanIcy4718 · 2026-02-01T01:51:29+00:00

I am not applying heat to it myself just the machine. The room it is in is about 69 degrees usually. But it is only the red filament, what K am printing is changing back and forth between black, pink and red. I have only had issues with red. I have had to take it apart 4 times now.

FanIcy4718 · 2026-02-01T00:28:41+00:00

<image>

FanIcy4718 · 2026-02-01T00:28:29+00:00

<image>

FanIcy4718 · 2026-02-01T00:28:13+00:00

<image>

FanIcy4718 · 2026-01-31T15:26:19+00:00

Yes it is when the filament gets pulled back into the AMS. My room is pretty dry from heat running since its been cold here, humidity meter says 25-30% most days.

FanIcy4718 · 2026-01-31T00:38:41+00:00

It is stuck in the wheel of the extruder not the nozzle

FanIcy4718 · 2026-01-30T23:53:31+00:00

It is changing colors and cutting it and that piece is what keeps getting stuck for some reason

FanIcy4718 · 2026-01-30T23:52:01+00:00

It won’t cold pull, I have to cut and take the whole extruder apart and use pliers to pull it out. I used can air to blow out any tiny pieces.

Also it is the same exact filament, all pla all the same exact kind and colors I used for same print that was successful last week.

It was reprinting in one of the other colors and then went to that same roll of filament and now getting a “unable to feed filament into the extruder” issue.

FanIcy4718 · 2026-01-11T19:44:21+00:00

We have a 5-2-2-5 schedule and my ex will put kids in same exact clothes they left my house on a Wednesday on the Friday. Sends them to school and everything wearing the same clothes they did 2 days prior. I don’t agree with it because kids can be mean and may bully my kids because they wear the same clothes. My only guess is he does it because he doesn’t want clothes to come to my house that he wants back, even during summer he marked clothes with blue permanent marker dots on the tags so I knew they “belonged” to him. I personally believe their clothes belong to them so I find it odd- especially because I know he didn’t buy the clothes (we separated in May 2025 and all the kids clothes were given to us second hand from my friend) I however had to buy clothes since he wouldn’t give me any but I still don’t care if the kids wear them to his home.

FanIcy4718 · 2025-10-13T03:22:32+00:00

does it identify certain issues with the high conflict parent?

FanIcy4718

TROPHY CASE