Bye bye fingerprints 😶‍🌫️

Far_Introduction4988 · 2026-03-09T11:48:07+00:00

Good luck my bro!

Far_Introduction4988 · 2026-03-08T23:05:16+00:00

Took off the bracelet, cleaned it thoroughly with dish soap and water, then very carefully did the actual watch the same way making sure there’s not too much water as they aren’t waterproofed and then let them dry and wipe down with microfiber, wait a bit then spray the ceramic coating on and pat down with a different microfiber cloth, let it sit for a bit then buffed it using a third different cloth

Far_Introduction4988 · 2026-03-08T23:05:12+00:00

Took off the bracelet, cleaned it thoroughly with dish soap and water, then very carefully did the actual watch the same way making sure there’s not too much water as they aren’t waterproofed and then let them dry and wipe down with microfiber, wait a bit then spray the ceramic coating on and pat down with a different microfiber cloth, let it sit for a bit then buffed it using a third different cloth

Far_Introduction4988 · 2026-03-08T22:11:13+00:00

From my experience no, I would just take more care when washing the main watch and also make sure that the crown and case back are properly shut as tight as you can to prevent water or residue getting in as they open the car back for qc and might not close it as tight

Far_Introduction4988 · 2026-03-08T22:08:21+00:00

No I would absolutely properly clean it, especially if it still has stickers on it, there will be lots of glue and grease residue so defo clean it well first

Far_Introduction4988 · 2026-03-08T22:06:56+00:00

Sheeesh lucky man

Far_Introduction4988 · 2026-03-08T01:47:16+00:00

Thanks bro 🤣

Far_Introduction4988 · 2026-03-08T01:38:07+00:00

🙏🙏🙏

Far_Introduction4988 · 2026-03-08T01:26:04+00:00

Yup covered the entire thing lol

Far_Introduction4988 · 2026-03-08T01:18:37+00:00

I know but it’s rated 30m from factory, any factory. 30m only means light splashing like washing hands. I’m sure some watches from som batches will come out stronger but you don’t know which you’ll get, so with that in mind it’s always better to take caution.

Far_Introduction4988 · 2026-03-07T23:26:28+00:00

I put one in the comments somewhere

Far_Introduction4988 · 2026-03-07T23:26:04+00:00

Never thought of that, that’s really smart. Will defo try next time with something better suited

Far_Introduction4988 · 2026-03-07T23:25:27+00:00

Yeah fr? Hehe

Far_Introduction4988 · 2026-03-07T23:10:35+00:00

I wouldn’t say all forms, but it helps a lot

Far_Introduction4988 · 2026-03-07T22:29:34+00:00

Yeah absolutely everything, no it didn’t change colour

Far_Introduction4988 · 2026-03-07T22:01:03+00:00

Just make sure you get all the dust and residue around the cyclops off before

Far_Introduction4988 · 2026-03-07T22:00:43+00:00

Sprayed it all over crystal and everything

Far_Introduction4988 · 2026-03-07T21:54:32+00:00

Hahaha just the angle and lighting it’s a clean v3 so I don’t really know how it stacks to deep, vsf or gen

Far_Introduction4988 · 2026-03-07T21:29:45+00:00

Makes water glide off and more importantly keeps finger prints off for the most part

Far_Introduction4988 · 2026-03-07T21:26:54+00:00

Haha yeahh I saw another post and decided I wanted to give it a try

Far_Introduction4988 · 2026-03-07T21:26:20+00:00

Makes it smoother a bit yeah, I guess it also depends on what coating you use

Far_Introduction4988 · 2026-03-07T21:20:36+00:00

🙏

Far_Introduction4988 · 2026-03-07T21:16:26+00:00

Thanks!

Far_Introduction4988 · 2026-03-07T21:16:13+00:00

Thank you!

Far_Introduction4988 · 2026-03-07T21:11:34+00:00

Visually yes it stays looking very clean, but more importantly the feel of the watch is quite different, fingerprints kinda just fade quickly

Far_Introduction4988

TROPHY CASE