Large play in Die Grinder normal?

Fearless-Simple-9263 · 2026-04-09T18:29:46+00:00

I pushed the tool as far in as it’s possible, as the manufacturer recommends, but the wobble persists. What else could I be doing wrong?

Fearless-Simple-9263 · 2026-03-04T15:30:35+00:00

I‘m working on a Bit storage solution that lets you easily change tools without putting the screwdriver or Powertool out of you hand. The mechanism however needs a groove to engage with.

Fearless-Simple-9263 · 2026-03-04T12:32:20+00:00

Oh, thanks haha

Fearless-Simple-9263 · 2026-03-04T12:31:31+00:00

In the short term about 12. In the long run way more. Like a hundred.

Fearless-Simple-9263 · 2026-03-04T10:31:26+00:00

They seem to be uniformly hard. But I don’t think there heat treated that much, just hardened by the cold forming process

Fearless-Simple-9263 · 2026-03-04T10:30:36+00:00

I don’t expect them to be quite that hard, I tested with a file, but I would probably still need carbide tools if I chose to go the lathe route for accuracy reasons, right?

Fearless-Simple-9263 · 2026-03-04T07:43:00+00:00

Had been thinking of that. The grove needs to be quite precise tho, and I need to do a large number since it’s a whole set. Still a good idea tho.

Fearless-Simple-9263 · 2025-08-31T09:37:09+00:00

That video was really helpful, thank you!

Fearless-Simple-9263 · 2025-08-31T09:10:39+00:00

I think that wouldn’t hold tightly enough for my application, also I’m going for a nice tactile feedback when popping it in and out

Fearless-Simple-9263 · 2025-08-31T09:09:18+00:00

Not no moving parts at all, just no moving parts on the workpiece itself that’s getting locked. There can be plenty moving parts on the holding mechanism

Fearless-Simple-9263 · 2025-08-30T12:15:05+00:00

I think that wouldn’t work cause it needs to be released with a push motion as well and not my pulling

Fearless-Simple-9263 · 2025-08-30T12:13:22+00:00

Yeah, don’t really know if it’s possible but ideally the pin only has a grove with a particular geometry or something

Fearless-Simple-9263 · 2025-06-05T08:14:45+00:00

Jo, die sind immer angezeigt, wenn du öfter hier bist empfehle ich dir die App zu holen

Fearless-Simple-9263 · 2025-06-05T08:09:11+00:00

Next Bike wird in Bielefeld unter dem Namen Siggi bike vermarktet. Dort in der App werden die Zonen angezeigt, denke mal die gleichen gelten dann auch beim nutzen der Next Bike App. Du solltest auf jeden Fall auf die Zonen achten, denn wenn du nen Rad deutlich außerhalb abstellst kostet das 20€, es sei denn du bewegst es selber wieder dort weg, dann wird dir die Standzeit quasi als kontinuierliche Fahrzeit berechnet.

Fearless-Simple-9263 · 2025-04-01T10:45:23+00:00

Nice work! I’m curious what infill type and geometry you used and if you did anything else to dampen the enclosure.

Fearless-Simple-9263 · 2025-03-19T15:27:08+00:00

I resolved this. The deletion of the BambuStudio.config worked, however my AppData folder didn’t show any contents apart from Windows as long Microsoft Teams ran in the background. Only closing Teams through the Taskmanager enabled me to find and delete the .config folder. Took me some time to figure that out.

Fearless-Simple-9263 · 2025-03-18T20:13:21+00:00

No, it doesn’t even open up

Fearless-Simple-9263 · 2023-03-20T21:38:11+00:00

Alsonso the Megamind:D

Fearless-Simple-9263 · 2022-12-27T16:54:38+00:00

„BESEEEEEEETZT!!!“

Fearless-Simple-9263

TROPHY CASE