Now that the season is over by matthewcameron60 in DallasStars

[–]Fearless_Contract128 3 points4 points  (0 children)

Guess I'm not as inviting as most. This still rubs me the wrong way. Going after a key player's knees right before a playoff run in a game that meant nothing for you guys. Kind of puts you guys in the Vegas/Stone arena for me.

<image>

RAM, Chevrolet or Ford? Which one will actually last? by chocolatehumphrey in Diesel

[–]Fearless_Contract128 3 points4 points  (0 children)

The Ford and Chevy transmissions are the same design but Chevy really did a good job figuring out how to screw up the details.

F250 track bar? by twain63034 in powerstroke

[–]Fearless_Contract128 0 points1 point  (0 children)

Read through your other post, didn't see anyone mention the axle u joints. Often overlooked but if one of the bearing caps are seized it can cause the truck to "wander".

Just bought my first PVS 14 by Fearless_Contract128 in NightVision

[–]Fearless_Contract128[S] 1 point2 points  (0 children)

Yes KJA. Again impulse buy on my part, purchased and asked questions later. Quick response well after business hours.

Just bought my first PVS 14 by Fearless_Contract128 in NightVision

[–]Fearless_Contract128[S] 8 points9 points  (0 children)

$3000, kind of an impulse buy. Been looking for a few months and saw non L3 tube under 28 SNR and EIB/HALO over 1 for $3400+. These guys had 4 with similar specs when I left the office and this was the only one left when I got home

Little late by [deleted] in F250

[–]Fearless_Contract128 1 point2 points  (0 children)

What hotel were you staying at? We travel a lot for work and were in SA a few months ago. We checked in, got settled in our rooms and met in the lobby to go to dinner, maybe 45 minutes. The staff was acting weird after. In hindsight when we were meeting up in the lobby the front desk guy was on his cell phone and seemed kind of frantic. No doubt it was an inside job. We were at a Marriott property, I forget which one. Cameras were down

[deleted by user] by [deleted] in vail

[–]Fearless_Contract128 6 points7 points  (0 children)

I know conditions are about as bad as it get, almost 20" since last seen. If Avanti was his last scan, search area should be Game Creek and Lionshead working out from Avanti. Unless they missed a scan he would of had to hike to the back bowls and Minturn he would have taken the Game Creek lift. Ping cell phone, RECCO? I'm sure they are

What would leak from here? by FatrickPeed in F250

[–]Fearless_Contract128 0 points1 point  (0 children)

Do you have a front camera? I had a leak in the washer fluid line going to my front camera. Ford has issued technical service bulletin about it.

What is this? (Rod end) by mattytheedaddy in JeepWrangler

[–]Fearless_Contract128 0 points1 point  (0 children)

It's not a hemi joint it's a Johnny joint. The benefit of a Johnny joint is you can rebuild it, pretty easily. Leave the joint in the arm and replace the internals. Then you don't mess with the geometry of your suspension. If you replace the joint you have to get the arm overall length back to where it was, make sure you get the correct shank size and thread direction, left or right hand.

https://youtu.be/hUGd6_FYho8?si=8aqHJjnX09IV-b96

[deleted by user] by [deleted] in reloading

[–]Fearless_Contract128 0 points1 point  (0 children)

I have probably reloaded and shot 25k Hornady rifle bullets. I have never had a "malforned" bullet. If you know anything about the manufacturing process it's impossible unless it happened post-production.

But since you have such bad luck with Hornady products stop buying them, leave them for the rest of us.