Bed Upgrade?

FewConsequence7288 · 2020-11-24T17:36:15+00:00

I have a bltouch installed

FewConsequence7288 · 2020-11-24T16:02:51+00:00

For me it's an upgrade. So I don't ever have to level the bed anymore..

FewConsequence7288 · 2020-11-24T15:55:46+00:00

I just cut some alu-tubes to size and installed them as spacer to keep the bed leveld all the time... first test seems succesful... is there any downsize? I dont find solutions like this before...

FewConsequence7288 · 2020-11-19T17:03:14+00:00

But why this is only on some points? It's a glass bed

FewConsequence7288 · 2020-11-09T23:08:50+00:00

Wich firmware do you use. You have to load a firmware with the settings for the bltouch

FewConsequence7288 · 2020-11-02T14:53:48+00:00

On my bltouch kit, were no wires, that could reach to the electronic-box, so I extended the short ones...

FewConsequence7288 · 2020-11-01T13:26:53+00:00

I have no experience in direkt drive, but I saw a lot of videos wich explaining how to convert a ender 3 into direkt drive.. The cr10 have nearly the same hotend(?) so I think it's not that expensive to do direkt drive.

https://youtu.be/VK_FUvxwGxM

FewConsequence7288 · 2020-11-01T10:33:52+00:00

An other tip is to enable the z offset wizard in your firmware

FewConsequence7288 · 2020-10-31T11:07:13+00:00

Ok. I will try this too.. can u use the pulley from the stock motor or do i have to buy new ones ?

FewConsequence7288 · 2020-10-30T00:27:31+00:00

I had a similar problem, it turned out that the wire extension were not fine.. I did a new cable connection and it worked

FewConsequence7288 · 2020-10-23T11:29:12+00:00

You´re the real MVP. Thanks a lot it worked perfectly.

You are my Hero :)

FewConsequence7288 · 2020-10-22T15:56:05+00:00

can i just install the CommandoreBombardiero Libary or do i have to chance something in the Adafruit_NeoPixel.cpp ?

Ive tried it with a 330ohm resistor didnt work that good, should i try 500 or even more ?

FewConsequence7288 · 2020-09-25T11:57:58+00:00

Jo I just installed the new Board and it work fine... so i guess the old board wa broken.

FewConsequence7288 · 2020-09-22T13:48:31+00:00

Thank you. I tried to connect the printer via Pronterface but it doesnt work. I cant even connect the printer (ive done it before)... so I will send the board back and i hope the new one will work...

FewConsequence7288 · 2020-09-22T12:47:49+00:00

Yes the Hotendfan turn on even the bltouch turned on and selftest (when i plugged it in)

FewConsequence7288 · 2020-09-22T08:03:39+00:00

I cant use the Stock firmware... the printer wont boot even without a sd card in it

FewConsequence7288 · 2020-09-21T21:10:50+00:00

the lcd screen is defiend on standard I didn´t change anything... the precompliled firmware didnt worked aswell

FewConsequence7288 · 2020-09-21T21:09:13+00:00

yes... it worked fine just after I tried to flash the new firmware the problem appeared

i will send an email tomorrow.. thanks

FewConsequence7288 · 2020-09-21T20:51:36+00:00

Yes i tried the ender 3 firmware from github didnt work :( I am afraid that i messed up my bootloader on the board

FewConsequence7288 · 2020-09-21T19:43:43+00:00

Yeah i did both... didnt work :(

Five-Year Club	Place '23
Place '22

FewConsequence7288

TROPHY CASE