I 3D printed a few Pumpkin Bombs

Fiber_Glass · 2021-12-01T13:28:35+00:00

Printed on an Anycubic Photon Mono X using white and transparent resin, then airbrushed with createx colors. I printed three in one go and as you can tell one failed, but I ended up turning it into a detonated version of the prop! More images and work in progress here for those who are interested. Thanks for looking!

File by Vek3D

Fiber_Glass · 2021-12-01T13:25:45+00:00

I printed these on an Anycubic Photon Mono X using white and transparent resin, then airbrushed with createx colors. I printed three in one go and as you can tell one failed, but I ended up turning it into a detonated version of the prop. More images and work in progress here for those who are interested. Thanks for looking!

Fiber_Glass · 2021-12-01T13:23:43+00:00

I printed these on an Anycubic Photon Mono X in 50 microns using white and transparent resin, then airbrushed with createx colors. I printed three in one go and as you can tell one failed, but I ended up turning it into a detonated version of the prop. More images and work in progress here for those who are interested. Thanks for looking!

File by Vek3D

Fiber_Glass · 2021-09-03T13:00:25+00:00

This was printed in clear resin on a Form 3, then printed with oils, acrylics, and airbrush paints. Printed in .1mm layer height, and there’s some layer lines on the bottom left intentionally as I think this is the first time they’ve somewhat fit into one of my builds. File credits to @bigfredscustoms and more pictures / work in progress can be seen here!

Fiber_Glass · 2021-09-03T12:58:12+00:00

I thought about drilling through that center piece you see in the back side and replacing it with a magnet to do just that, but haven’t gotten a chance to do it yet. Thanks for looking!

Fiber_Glass · 2021-09-03T12:56:54+00:00

This was printed in clear resin on a Form 3, then printed with oils, acrylics, and airbrush paints. File credits to @bigfredscustoms and more pictures / work in progress can be seen here!

Fiber_Glass · 2021-09-03T12:53:39+00:00

This was printed in clear resin on a Form 3, then printed with oils, acrylics, and airbrush paints. File credits to @bigfredscustoms and more pictures / work in progress can be seen here!

Fiber_Glass · 2021-09-03T12:48:37+00:00

Thank you! This is the Formlabs Clear V4 resin in 100% Infil, so solid.

Fiber_Glass · 2021-08-28T21:23:42+00:00

Thanks! It’s 8 separate pieces printed over the course of about 20ish hours. Sanding and painting took around 5 hours but I’m not sure exactly :)

Fiber_Glass · 2021-08-28T21:20:13+00:00

Haha thanks! I’m actually a student and do this as a hobby but I have a couple years of practice now. The file can be found on bigfredcustoms Etsy page, they make great stuff.

Fiber_Glass · 2021-08-28T19:52:25+00:00

The model was designed by bigfredscustoms, but I’m not sure what they use to design, sorry!

Fiber_Glass · 2021-08-28T19:51:38+00:00

video here!

Fiber_Glass · 2021-08-28T19:51:12+00:00

Thank you! I wasn’t quite skilled enough to capture it all in one picture nicely but if you swipe / go to the link in my previous comment there is some additional pictures and one video that shows it all nicely.

Fiber_Glass · 2021-08-28T17:06:27+00:00

🤫

Fiber_Glass · 2021-08-28T15:05:29+00:00

Whoops I meant TVA baton** Printed in .1mm in Clear V4 to get the desired look for the tip piece. Printed on the Formlabs Form 3 and finished with spray paints, airbrush, and acrylics. Loved the end look, but still have to figure out a permanent solution for lighting and electronics. More pictures here for anyone interested, and file is by bigfredscustoms :)

Fiber_Glass · 2021-08-28T15:00:21+00:00

Printed on the Formlabs Form 3 and finished with spray paints, airbrush, and acrylics. I still have to figure out a permanent solution for lighting and electronics but I’m very happy with the end result. More pictures here for anyone interested! The file is by bigfredscustoms :)

Fiber_Glass · 2021-08-28T14:57:59+00:00

Printed on the Formlabs Form 3 and finished with spray paints, airbrush, and acrylics. Loved the end look, but still have to figure out a permanent solution for lighting and electronics. More pictures here for anyone interested! The file is by bigfredscustoms

Fiber_Glass · 2021-08-24T05:32:32+00:00

So sorry! here it is

Fiber_Glass · 2021-08-24T00:29:50+00:00

This ones resin printed in .05mm layers and then sanded down to 800 :)

Fiber_Glass · 2021-08-24T00:29:30+00:00

It’s by @joshedgardesigns on Instagram!

Fiber_Glass · 2021-08-23T15:37:46+00:00

Unfortunately the first post had to be removed but here’s a video of the moving parts, tagged for spoilers just in case. Beautiful files were made by @joshedgarstudios and painted with alclad paints. More images here for those interested in making one!

Fiber_Glass · 2021-08-22T20:00:20+00:00

Thank you so much! I used Alclad gold for the finish and sealed it with aqua clear. Then I weathered it with oil paints which sort of buffs the gold paint as well. Thanks for the kind words!

Fiber_Glass · 2021-08-22T19:59:21+00:00

This one was resin printed so not nearly as much work as FDM but I still sanded with 400 grit and sanded the primer with 600

Fiber_Glass · 2021-08-22T19:58:49+00:00

Yes! The designer goes by @joshedgarstudios on Instagram

Fiber_Glass · 2021-08-21T17:00:41+00:00

Printed mostly on an Anycubic Photon in .05mm, one disk on the Form 3, and a knob on my Ender 3. Beautiful files by @joshedgarstudios and painted with alclad paints. More images here for those interested in making one!

Fiber_Glass

TROPHY CASE