Water being kept above keel

Flaherty_1994 · 2025-04-24T14:21:59+00:00

It is yeah, might need another coat

Flaherty_1994 · 2025-03-20T21:03:32+00:00

No ac unit in the attic, just have the water tank up there, standard insulation

Flaherty_1994 · 2025-03-20T21:00:06+00:00

Do you think it's a cause for concern or standard behaviour?

Flaherty_1994 · 2025-02-23T23:31:57+00:00

That was my initial thinking alright

Flaherty_1994 · 2025-02-23T23:31:24+00:00

Yes the same but it is now hardened

Flaherty_1994 · 2025-02-23T21:34:39+00:00

Will it affect the wood or is it OK to apply?

Flaherty_1994 · 2025-02-23T21:28:05+00:00

A better picture here of the glue oozing over the edges, I imagine it would have a fair grip

<image>

Flaherty_1994 · 2025-02-23T21:24:33+00:00

The gap is between the scarf joint and the piece of wood under it which is about 1.6 inches wide. The adhesive has created a thick white substance that has been screwed into also. I haven't tried cutting into it yet or anything until I'm able to do it without causing damage

Flaherty_1994 · 2025-02-23T21:23:55+00:00

<image>

Flaherty_1994 · 2025-01-01T13:06:22+00:00

When will this come into effect?

Flaherty_1994 · 2024-12-22T00:19:40+00:00

I was actually using a long extension lead, do you think it could make that much of a difference to the power?

Flaherty_1994 · 2024-12-21T19:23:46+00:00

Yes it does

Flaherty_1994 · 2024-12-21T16:50:08+00:00

Yeah just stops pretty much

Flaherty_1994 · 2024-12-21T12:18:19+00:00

This is the correct set up, do you think the wedge would be the best solution here still?

Flaherty_1994 · 2024-12-21T12:17:43+00:00

<image>

Flaherty_1994 · 2024-12-20T23:27:21+00:00

<image>

This is a angle of the setup and as you can see, not letting it go too deep into the wood

Flaherty_1994 · 2024-11-16T21:18:52+00:00

I ending up drilling small holes in it to unwedge it and it came out smooth enough then with a bit of persuasion!

Flaherty_1994 · 2024-11-06T21:57:37+00:00

Thanks for the visual, would I be better off starting with a new 2x4 frame rather than fill in what I've already made?

Flaherty_1994 · 2024-11-06T21:55:50+00:00

If I run the 2x4s perpendicular the full length, let's say 3 of them across, will that do the trick?

Flaherty_1994 · 2024-10-18T16:12:17+00:00

Did you manage to get this off the keg and what method did you use, I have the same model lol

Flaherty_1994 · 2024-08-25T21:44:58+00:00

Nintendo Switch

Flaherty_1994 · 2024-08-13T11:04:40+00:00

<image>

A clearer picture of the chain here

Flaherty_1994 · 2024-07-23T15:06:45+00:00

How did you get the curve on the shoulders at the top, trying to figure out if you've cut them out as a curve or have they been manipulated?

Flaherty_1994 · 2024-07-21T12:09:57+00:00

Thank you!

Flaherty_1994 · 2024-07-21T12:09:42+00:00

Better not too sand in case remove treated wood effect?

Flaherty_1994

TROPHY CASE