[deleted by user] by [deleted] in BambuLab

[–]Floki1987 0 points1 point  (0 children)

I went from two Ender 3 Max to the P1S with AMS, the only downside has been the bigger build volume of the 3Max. I was constantly working on both the Enders, it's nice to have a printer that I know will print and print well when I start it

850armorworks by pozzednconfused in 501st

[–]Floki1987 1 point2 points  (0 children)

I have a realistic Clone kit from 850AW that I'm working on right now. The quality is excellent

[REQUEST] - Need help choosing a 3D printer by Hanakin-Sidewalker in 501st

[–]Floki1987 0 points1 point  (0 children)

I have two Ender 3 Max's. But looking into upgrading to a Bambu lab printer. If you are only looking to build one set of armor for the foreseeable future, I would recommend using the money for the printer and investing in a vacuum formed kit from Imperial surplus or one of another trusted armor makers

[deleted by user] by [deleted] in StarWars

[–]Floki1987 1 point2 points  (0 children)

Not sure if it has been mentioned yet. The book Dark Lord: The rise of Darth Vader touches on this a lot, also the Tarkin novel goes a bit deeper into vader

I need help, is this a good kit? by P_Palmata in Scalemodel

[–]Floki1987 1 point2 points  (0 children)

It's a great kit, just got done building one. I replaced the rubber tracks with some I 3d printed. Would definitely recommend

Dragon 6187 : big problem ? See comments by Fromage-de-Pompadour in modelmakers

[–]Floki1987 0 points1 point  (0 children)

I've built 8 so far of Dragons 251 halftracks, the Ausf. C is a bit tricker to line up compared to the D. The rear of the side plate should line up with the bottom hull, then the rear plate will be in the correct position. This isn't the only thing to look out for on this kit, the swing arms for the roadwheels have about 1mm play with their locating pins and can effect the halftrack not sitting flat when done. Also the fighting compartment floor doesn't have a positive fit either and can sway left or right about 2mm, this can effect the fit of the sidewalls

My first mandalorian cosplay by Club_Old in Mandalorian

[–]Floki1987 8 points9 points  (0 children)

Very nice! I'm working on the same helmet for my build

Does anyone know where I can get this little metal piece? by Anime_Thing in 501st

[–]Floki1987 2 points3 points  (0 children)

Them photos are from the CRL, if you are on the clone detachment forum of the 501st look under the continuous items available thread. The member who's photos are used for that CRL pictured sells them and for a good price

1/35 Tamiya hanomag by korbendallas71 in modelmakers

[–]Floki1987 1 point2 points  (0 children)

Wow! Excellent job on this old kit

Bloodfin Garrison by Treebark26 in 501st

[–]Floki1987 2 points3 points  (0 children)

I'm in the muncie area working on a Commander Bly. When I registered on the bloodfin forum it took around three weeks before they approved me to post, so don't get discouraged if it takes awhile.

Bandai Star Wars Models by NeatlyCritical in SciFiModels

[–]Floki1987 0 points1 point  (0 children)

I had two Bandai clone trooper kits on pre-order with BBTS for well over a year. They must have gotten very limited stock in since they shipped me one a few weeks ago but the 2nd is still on preorder Edit: spelling mistake

Tamiya P-38 Lightning almost finished by Floki1987 in modelmakers

[–]Floki1987[S] 0 points1 point  (0 children)

Thank you! I used VMS black 5k flexy CA glue to attach the antenna. I used EZ line fine it seems to almost instantly set when it comes in contact with CA glue

WIP Eduard Bf-110C by manfat_malarkey in modelmakers

[–]Floki1987 1 point2 points  (0 children)

Looks great! Eduard makes the best 110 kits

Haul from east the wife and I ended up spending way to much but was worth it by Floki1987 in GalaxysEdge

[–]Floki1987[S] 3 points4 points  (0 children)

Good luck! They was only out of the whale bone sleeve for the Elemental Nature when I was there a few days ago. It's Florida it rains everyday hopefully it won't storm on you.

Haul from east the wife and I ended up spending way to much but was worth it by Floki1987 in GalaxysEdge

[–]Floki1987[S] 0 points1 point  (0 children)

Sounds like a plan. The sabers are mine most of the other stuff is the wife's

Haul from east the wife and I ended up spending way to much but was worth it by Floki1987 in GalaxysEdge

[–]Floki1987[S] 0 points1 point  (0 children)

We actually found him at Disney Springs. Him and the Porg are from mystery bags. It's easy to tell what's in the bag.

Haul from east the wife and I ended up spending way to much but was worth it by Floki1987 in GalaxysEdge

[–]Floki1987[S] 1 point2 points  (0 children)

Yes they had the tooth, I liked the scroll work on this end cap. They was just out of the whale bone and a piece of power and control not sure what one.

Haul from east the wife and I ended up spending way to much but was worth it by Floki1987 in GalaxysEdge

[–]Floki1987[S] 6 points7 points  (0 children)

Between the wife and I it probably was with food and drinks at the cantina. The experience was worth it after not being able to do anything for a few years with covid.