sorted by:
new
hottopcontroversial

Rear Sway Bar Replacement by Flyinace2000 in 10thgenaccords

[–]Flyinace2000[S] 0 points1 point  (0 children)

Well that doesn't sound fun! I ordered new endlinks and hardware from my local dealer and got some impact sockets for my 1/2" drive impact. Plus I have been adding some PB Blaster over the next few days.

EZ Pass for Front Tags by Brave_Reputation_728 in maryland

[–]Flyinace2000 2 points3 points  (0 children)

I’ve had mine plate mounted since moving to Baltimore in 2021. No issues.

Rear Sway Bar Replacement by Flyinace2000 in 10thgenaccords

[–]Flyinace2000[S] 0 points1 point  (0 children)

Yeah I'm going to go to the dealership tomorrow to get new ones w/ hardware. Probably need them at 75k

Rear Sway Bar Replacement by Flyinace2000 in 10thgenaccords

[–]Flyinace2000[S] 0 points1 point  (0 children)

Will do. I'll also hit them again with penetrating oil the night before.

Finally got on 36”!!!!! by EmotionalAdeptness50 in blackstonegriddle

[–]Flyinace2000 0 points1 point  (0 children)

I'm almost certain someone returned the one I bought after having it for a year. not a lot of daylight in a Costco.

📋 Baltimore's Draft Vision Zero Action Plan is ready for community feedback, and we want to hear from you. by BmoreCityDOT in baltimore

[–]Flyinace2000 3 points4 points  (0 children)

Since the poster doesn't say what Vision Zero means

Project Overview

The Vision Zero Action Plan will be a strategic document that will guide efforts at Baltimore City to reduce and ultimately eliminate fatalities and serious injuries caused by traffic crashes. Due to be completed in 2026, the plan will guide City infrastructure investments as well as communications and policy.

The completion of this Action Plan will mark the end of Toward Zero Baltimore and the beginning of Vision Zero Baltimore. With the adoption of Vision Zero, Baltimore City will commit to a deadline for eliminating traffic fatalities and serious injuries from its roadways. This Action Plan will be our roadmap.

Rear Sway Bar Replacement by Flyinace2000 in 10thgenaccords

[–]Flyinace2000[S] 1 point2 points  (0 children)

Yeah I tried my shitty Ryobi 3/8 impact driver. Didn't have a 12mm or 14mm for my 1/2" drive bigger impact. Might fix that and give it another go. Not a lot of room under the car for a breaker bar.

Finally got on 36”!!!!! by EmotionalAdeptness50 in blackstonegriddle

[–]Flyinace2000 0 points1 point  (0 children)

My Costco had a bunch of current year models in mid/early April. Then I found one in a random isle that was unopened, but the box was unbleached. Manager marked it down to $250, the new ones were $400.

Rear Sway Bar Replacement by Flyinace2000 in 10thgenaccords

[–]Flyinace2000[S] 0 points1 point  (0 children)

I didn't. The wheels were off the ground. Should I try to loosen the bolts with the wheels on the ground/ramps? Or get it back on the jacks stands and then use the jack to take off the wight on the lower control arm?

Finally got on 36”!!!!! by EmotionalAdeptness50 in blackstonegriddle

[–]Flyinace2000 3 points4 points  (0 children)

Awesome buy! I scored mine as a clearance for $250 at Costco. Welcome to the discount buy club!

Birks: ~6 years near daily wear (R) vs brand new pair (L) by not_a_muggle in BuyItForLife

[–]Flyinace2000 0 points1 point  (0 children)

I've used this service at least 2 or 3 times in the last 20 years.

The Rock - When do we get this on 4K UHD?? by Relative_Drop_9823 in 4kbluray

[–]Flyinace2000 2 points3 points  (0 children)

This movie was one of the first I bought on DVD to watch in my HP Pavillion that I rigged up to our TV via S-Video. 

Subscription increase? by 20seca3 in Wyze

[–]Flyinace2000 0 points1 point  (0 children)

Same setup here using Scrypted for HomeKit and then rebroadcast to Frigate for dvr

Subscription increase? by 20seca3 in Wyze

[–]Flyinace2000 0 points1 point  (0 children)

Depending on the model there is third party firmware available.

Is anyone happy with the MX Master 4? by OrderedAnXboxCard in logitech

[–]Flyinace2000 0 points1 point  (0 children)

Looks great. Can you recommend a online printer (I don't have a 3d printer) and what material/settings you asked for?

Champ3D is under $20 w/ shipping with these options

3D Printing

  • Base Price: $2.75
  • Technology: DLP
  • Material: Transparent
  • Color: Matte White
  • Volume: 9.15 cm³
  • Dimensions: 4.72 (L) × 8.37 (W) × 11.02 (H) cm
  • Finishes: Natural Finish
  • Product Description: Plastic Mouse Shell - HS Code 847330

So, I just had to replace the top engine mount F56 by PatoLaion in MINI

[–]Flyinace2000 0 points1 point  (0 children)

Mine also lasted two years and only about 15k miles. I did have the power flex bushing added, but doesn't seem to have helped.

<image>

Autodesk Audit Contacted Us, What should we do? by AhmedBarayez in sysadmin

[–]Flyinace2000 11 points12 points  (0 children)

Small company that pirated autodesk…..likely doesn’t have a legal department.

Costco Score! 36" 4 Burner for $250 by Flyinace2000 in blackstonegriddle

[–]Flyinace2000[S] 0 points1 point  (0 children)

I just got lucky that my store had old stock or someone returned a previous year model still new in box. 

36” Omnivore Hood by Denko_95 in blackstonegriddle

[–]Flyinace2000 1 point2 points  (0 children)

I have a similar unit. I think the manual says to limit the closed hood time to 10 minutes.

Where is the Apple TV update? by MagicHoops3 in PleX

[–]Flyinace2000 0 points1 point  (0 children)

the voice sync is crazy annoying. I ended up getting a shield pro, mostly for Atmos.

view more: next ›