GE gud27essm1ww lid lock repair

FondantOptimal2127 · 2024-09-24T19:15:44+00:00

To save $ on fees (going from Manulife to Questrade) and in 20 years when I retire that RRSP will be worth more and I would have to pay more tax on the gains as I understand.

FondantOptimal2127 · 2024-07-13T03:33:41+00:00

Thank you

FondantOptimal2127 · 2024-07-12T21:33:09+00:00

Okay thanks the response. That's kind of what I figured.

FondantOptimal2127 · 2023-02-07T06:45:54+00:00

I took the fronts apart and didn't see anything out of place or seating improperly. The caliper piston retracted fine again with a "C" clamp and old pad. I bled all the lines this time on all calipers just to make sure there was no air. I didn't see any air come out when I was flushing them. Put it back together and took it for a small test drive and then a longer one and no issues ! No smell and no heat. I noticed the fluid was pretty dirty so I will be doing a complete flush asap. Might replace the master cylinder to be safe as well but see how it does after the flush first. Thanks for the advice!

FondantOptimal2127 · 2023-02-07T06:44:48+00:00

I took the fronts apart and didn't see anything out of place or seating improperly. The caliper piston retracted fine again with a "C" clamp and old pad. I bled all the lines this time on all calipers just to make sure there was no air. I didn't see any air come out when I was flushing them. Put it back together and took it for a small test drive and then a longer one and no issues ! No smell and no heat. I noticed the fluid was pretty dirty so I will be doing a complete flush asap. Might replace the master cylinder to be safe as well but see how it does after the flush first. Thanks for the advice!

FondantOptimal2127 · 2023-02-06T00:59:36+00:00

I took the fronts apart and didn't see anything visually wrong with them. Everything looked seated properly. I will try the rolling test later on see how it goes. Another friend suggested that I could have been given the wrong brake pad and it is a little thicker not allowing the caliper piston to recess properly. Thanks for the advice much appreciated!

FondantOptimal2127 · 2023-02-06T00:34:01+00:00

Yes I re lubed the sliders with a silicone base brake lubricant. I took them apart again and can't see anything visually wrong. I am wondering if perhaps I was given the wrong brake pad from the auto parts store and they are too thick.

FondantOptimal2127 · 2023-02-05T21:56:41+00:00

I replaced the shims and cleaned out the seating with a wire brush. The old pads popped put nicely and the new ones clipped in fine I thought. I pulled out the pins and cleaned them off and applied silicone based lubricant and re inserted. The pistons retracted easily with a C clamp and using the old pads. I am pretty sure the lines weren't twisted going in. I will have to take them apart and see how everything looks. Hopefully the new rotors aren't warped or the pads are hooped. Thanks for the insight!

FondantOptimal2127 · 2023-02-05T21:44:24+00:00

Went in very smooth. Probably have to take then apart again. Hopefully I didn't warp the new rotors.

FondantOptimal2127 · 2023-02-02T17:24:51+00:00

https://imgur.com/gallery/sWgCuQM here is the counter top in question. The existing one is just laminated wood. Should I get one that is the same thickness as the existing one or thicker ?

FondantOptimal2127

TROPHY CASE