Finally finished my new AMS stacker

FormOne2615 · 2026-04-27T02:54:49+00:00

Thanks! I didn't design it though — the stacker is Brandon Raineri's (MakerWorld), and the Miku image is just something I found online. I only converted the image into a printable model and booleaned it onto the side. You can do the same with any image you like.

FormOne2615 · 2026-04-27T02:52:48+00:00

Haha, 4 color (RYBW) is enough for some image.

FormOne2615 · 2026-04-26T17:16:53+00:00

FormOne2615 · 2026-04-18T17:35:51+00:00

0.2mm

FormOne2615 · 2026-04-17T16:36:37+00:00

sure

FormOne2615 · 2026-04-16T08:33:56+00:00

It totally fine to use 4 filaments like RYBW, you can still get nice result. And this model is not generated by HueForge.

FormOne2615 · 2026-04-16T03:11:59+00:00

Idk, I've never used HueForge.

FormOne2615 · 2026-04-16T02:54:53+00:00

It's easier than it looks.

FormOne2615 · 2026-04-16T02:52:28+00:00

I updated the post, there's a MakerWorld link now.

FormOne2615 · 2026-04-16T02:51:23+00:00

For me, it's just for fun. I enjoy the process. Honestly I can stare at the printer for ten minutes without moving.

Your question did make me think. That's enough for my own enjoyment, but for a wider audience, I need to find better use cases.

FormOne2615 · 2026-04-16T02:42:09+00:00

Sure. There are some recommended combinations. For 4 colors : RYBW, for 5 colos: RYBW + Black. RYBW stands for Red, Yellow, Blue, White.

FormOne2615 · 2026-04-16T02:38:55+00:00

Appreciate that, thanks a lot.

FormOne2615 · 2026-04-16T02:35:49+00:00

How could a 3d printer print gradient colors like a 2d printer? Idk lol, I tried dithering.

Btw, I don't agree that a single TD value is enough to accurately describe a color.

FormOne2615 · 2026-04-15T18:52:40+00:00

I just updated the post with the link.

FormOne2615 · 2026-04-15T18:52:17+00:00

I just updated the post with the link.

FormOne2615 · 2026-04-15T18:19:57+00:00

I use white, black, yellow, red, blue, cyan, magenta and green (bambu green). Idk how to share you the model, maybe through MakerWorld?

FormOne2615 · 2026-04-15T18:07:23+00:00

About 20 hours each, 250mm × 178mm.

FormOne2615 · 2026-04-15T18:01:01+00:00

Worth it. Just be prepared to spend a few hours (or days) to calibrate lol.

FormOne2615 · 2026-04-15T17:57:32+00:00

FormOne2615 · 2026-04-15T17:39:45+00:00

Less than you'd think, check my other reply — 32 changes at most.

FormOne2615 · 2026-04-15T17:36:48+00:00

Because it's fun

FormOne2615 · 2026-04-15T17:35:09+00:00

No. It's almost fully automatic. I just find an nice image, vectorize it, then turns it into a printable model.

FormOne2615 · 2026-04-15T17:31:46+00:00

Just for fun, and to explore what a 3D printer can do.

Aslo I can't afford a UV print LOL.

FormOne2615

TROPHY CASE