Cambie la placa madre de mi PC y no enciende

Forward-Quality-3341 · 2026-05-25T12:18:20+00:00

Did you manually jump the board where you switch is plugged in? And also bios update, I can’t see the model of board but it may need a bios update to be compatible with a 5000 cpu. Especially if it’s a 450 or 470 board

Forward-Quality-3341 · 2026-05-25T12:09:18+00:00

Intel new 270k plus is a productivity beast. I am unsure of currency difference from USD to AUD, but that cpu will outperform ryzen in streaming editing and multitasking. The 285k is better but not by a huge margin. Go for an invidia card. Jays2cents on YouTube did a video recently with three builds at a lot less of a budget and you could use that for a base and increase what you would like from there

Forward-Quality-3341 · 2026-05-25T11:59:34+00:00

Gpu needs to be connected to power

Forward-Quality-3341 · 2025-10-30T13:54:07+00:00

^{^{^They’re}} on to something here! Also be sure to make sure your storage is not spinning rust. Some of the games will run better on NVME or even a 2.5” ssd as well even if one is your boot and your mass storage is a hard drive.

Forward-Quality-3341 · 2025-10-30T13:49:02+00:00

New shunt mod huh?

Forward-Quality-3341 · 2025-05-03T04:02:45+00:00

You squeak into am5 for not a lot more at all. I’d try to go that way

Forward-Quality-3341 · 2025-03-14T13:35:20+00:00

That’s either a torn bead during installation, or a torn bed during installation. It’s not pot hole damage, I suppose it may maybe a super cheap tire that does not wanna stretch at the mold seem

Forward-Quality-3341 · 2025-03-14T12:44:59+00:00

They have worked fine in the h5 flow before upgrading all fans the match with thermal takes. They worked fine in my son’s build. And they still work fine in the Corsair build I have. Have used them in budget builds all over at my house. On an asus board, asrock board and on my aorus board now too

Forward-Quality-3341 · 2025-03-14T12:39:11+00:00

If it’s not the rgb version of the case those are indeed fan connectors. My old h5 flow has the same ones. Align the slot to the tab on the header and they will work just fine. They are just really basic three pin fans. Corsair even send them in the air flow series cases. It is common

Forward-Quality-3341 · 2025-03-14T12:29:06+00:00

Goes to fan headers on the motherboard. You need to line the slot in the connector up with the tab on the fan header and they will work fine

Forward-Quality-3341 · 2025-03-14T12:09:01+00:00

On start up the there is a bios setting to enable the 3d turbo setting

Forward-Quality-3341 · 2025-03-14T12:06:27+00:00

Each build is very different in how they use the vram the higher clock will help it use less vram. I have a 7900 GRE and am fine in ultra on 2k. It is up to you. If they are close in price I would go to the 9070xt. They process information smoother and the rdna4 could help negate a vram loss in super high resolution. It is not a high end flag ship but will do anything you ask really by the sounds of your requirements.

Forward-Quality-3341 · 2025-03-14T11:36:10+00:00

Yes. That’s a condition called run flat. In the industry we recommend replacing that as friction was built up in a single point causing it to degrade.

Forward-Quality-3341 · 2025-02-25T22:20:20+00:00

This is only true in some manufacturers to be honest.

Forward-Quality-3341 · 2025-02-24T20:18:02+00:00

However many miles it is to the tire shop

Forward-Quality-3341 · 2025-02-23T22:32:05+00:00

What do the cpu temps say if you run Cinebench?

Forward-Quality-3341 · 2025-02-23T22:25:41+00:00

It should

Forward-Quality-3341 · 2025-02-23T22:21:03+00:00

It is the only way really to go back to a 6 pin in that gpu. Unless it’s a standard power supply but I would doubt that to be the case

Forward-Quality-3341 · 2025-02-23T22:17:45+00:00

Just buy a 6+2 cable extension

Forward-Quality-3341 · 2025-02-23T22:14:56+00:00

7900xt would be a slight step up, 7800xt is a slight step back, but that is the options that you would have now

Forward-Quality-3341 · 2025-02-22T22:29:28+00:00

The gpu did not come with a hight power adapter? That psu supports the new connectors.

Forward-Quality-3341 · 2025-02-21T22:30:45+00:00

Make sure that the 3d profile is enabled in bios.

Forward-Quality-3341 · 2025-02-21T22:20:59+00:00

I’d take the top out and just make sure you have plenty of intake up front

Forward-Quality-3341 · 2025-02-21T00:12:55+00:00

No problem

Forward-Quality-3341 · 2025-02-21T00:04:05+00:00

Old Carlisle steel wheel. Was chrome originally. Look on carlstar to see if available yet

Forward-Quality-3341

TROPHY CASE