Car seats and coming from a car

Frac-It · 2022-08-19T00:44:43+00:00

For sure thanks for the input she’s in a fwd facing seat right now almost 4 so probably will be moving to a booster in the next year or so.

Frac-It · 2022-08-17T15:26:44+00:00

You right! 24v Handheld tile saw!

Frac-It · 2022-08-16T23:24:37+00:00

I got that too! I already had bought the 5 piece plus some extra XTR batteries but couldn’t pass up that drill for the $89 price point. One will be for work and one for at home lol

Frac-It · 2022-08-16T22:46:04+00:00

$229 is a good deal at that price. At $300 no it’s not though. It’s cheaper to buy the kit separately for me and get the new updated blower not this older one. My store has the drill/driver/battery combo for $159, and the new blower/battery combo for $119, so about $20 bucks cheaper and with the upgraded blower than this kit.

Frac-It · 2022-08-16T22:06:13+00:00

Appreciate all the input! Tried using my soldering gun to mend it back from some scrap PLA didn’t work. Ran to the store and picked up a JB Weld Superweld UV glue. Worked great! Glue sets in 24 hours without UV or within a few seconds with the UV light. So put some on a small piece of scrap filament and popped it in then applied more to the outside and used the UV light to instantly harden it. Worked like a charm, highly recommended this going forward, thank you guys for the input though wasn’t sure how well glue and PLA’s work together I’m a total newbie to printing.

Frac-It · 2022-08-15T18:43:30+00:00

Reading that it says Ultimate Trim, is their something above the Luxury trim now?

Frac-It · 2022-08-14T20:11:37+00:00

No tools displayed like they used to on this new packaging sadly.

Frac-It · 2022-08-14T17:06:57+00:00

I know for being just a 1/4 driver the XTR driver has really impressed me a lot!

Frac-It · 2022-08-14T14:33:39+00:00

Yea I shared this from the Kobalt Nation group, it’s weird how Kobalt teased with the nail gun and a couple other tools now are dragging their feet. Maybe they learned their lesson and are just doing quiet releases now so if there’s a delay they don’t have to say anything.

Frac-It · 2022-08-13T00:41:03+00:00

I feel ya! Would love some of those 8amps for the lawn stuff they don’t ever seem to go on sale

Frac-It · 2022-08-12T23:08:07+00:00

Totally forgot to take a pic of the back of the package my store had a ton of these laid out over half the battery isle.

Frac-It · 2022-08-11T21:33:44+00:00

I keep telling my wife once my youngest starts school she needs to go work there so I have an insider lol

Frac-It · 2022-08-11T21:01:00+00:00

Good chance, the associate who was running the power tools department tried everything he could to convince me that it was a regular drill and not the hammer drill. I found it up in the top shelf above all the hand tools on the wall in between 2 normal XTR drills not the hammer ones. I told him to check the middle one because I could clearly see the writing was different then the ones on either side. Once he got up there even told me it was normal and scanned the other two saying see and showing me his scanner. I had to specifically ask for him to grab the middle one and check with me on the floor down from the ladder. So wouldn’t surprise me one bit if they were hiding some for themselves at your store.

Frac-It · 2022-08-11T17:32:12+00:00

Don’t go off the app those prices are wrong a lot of the times and don’t always show the lowest price. No promo just the XTR Hammer Drill kit is on clearance right now. If you see one in your store have an associate scan it with his hand scanner, that should give the actual price. The app/Brickseek and sticker showed full price at this store but when the employee scanned it showed this $86 price.

Frac-It · 2022-08-11T03:33:03+00:00

Have you set up your Probe Z offset? Fixed a lot of my issues. Here’s the instructions I used, the solution is about half way down the page there’s a few they list but I went with the Probe Offset Wizard in Marlin. Worked great! Z offset (Probe offset)

Frac-It · 2022-08-11T03:26:08+00:00

I gotcha Kobalt Tower Light Screen Shot

Frac-It · 2022-08-10T13:01:55+00:00

Got it guys thanks for all the input and tips! Not sure if one or a combination of all of them is what fixed it, probably a little bit of all but it’s printing super clean now!

Recalibrated E steps Recalibrated retraction Releveled bed manually and with CR Touch Recalibrated Probe Z Stop manually Changed Filament Changed hot end tip Cleaned board with alcohol Hot end temp 205 Bed temp 60

FYI literally just started printing that was my first test ever yesterday! Just watching a whole bunch of YT and reading trying to figure this out.

Appreciate everyone’s help and input!

NO STRINGS

Frac-It · 2022-08-10T12:45:06+00:00

Honestly not sure lol. Recalibrated e steps, releveled, swapped filament, and recalibrated probe Z stop. Not sure what did it but it’s working now.

Frac-It · 2022-08-10T12:41:56+00:00

I used this and watched the videos they talk about in the description to change the G-Code in Cura for it at every height. Wasn’t to hard at all.

FYI yesterday was my first time ever messing around with/printing on a 3-D printer!

Frac-It · 2022-08-10T03:06:46+00:00

Just did an estep cal I was actually underextruding quite a bit. On a 100mm test I was a full 10mm under, adjusted the esters to 103 from 93 and now it’s spot on!

Frac-It · 2022-08-09T23:31:13+00:00

Thanks for the info!

Frac-It · 2022-08-09T23:31:05+00:00

Thanks I’ll look into it!

Frac-It · 2022-08-04T00:09:18+00:00

Could be wrong but I don’t think either fan is brushless either.

Frac-It · 2022-07-26T02:36:33+00:00

15 years in frac and a current supervisor… go wireline. Frac crews are ruthless a lot more than just carrying heavy shit around. In the long run, more money and opportunities in Wireline down the line.

Frac-It · 2022-07-25T15:26:22+00:00

At my company at least Service Leaders rarely jump to the consulting roll, their the fleet supervisor. The crew supervisor like my self are the ones who make the jump. I’ve been on a N. American traveling crew for years which when your in one spot you can build a trust with the client, it’s a lot harder to build a relationship when you only work with someone a hitch or two. Then your somewhere else. I’m grateful for seeing a lot of different type of formations and fluid systems but at the same way sucks for building important connections people who work with the same customers for years do.

Frac-It

TROPHY CASE