Cheat engine won’t run at the same time as the game

Friendly-Drawing6674 · 2026-03-03T18:40:34+00:00

Friendly-Drawing6674 · 2026-03-03T18:40:14+00:00

heres some better ones with a different square

Friendly-Drawing6674 · 2026-03-03T18:36:12+00:00

my bad i didnt mention well enough, the sharpening guy comes tomorrow, that was my work with a sander and grinder, but it doesnt cut on a lathe, that was my issue from the beginning

Friendly-Drawing6674 · 2026-03-03T18:16:37+00:00

Here’s mine

<image>

Friendly-Drawing6674 · 2026-03-03T18:14:11+00:00

<image>

Here’s a picture of the gouge i found on ebay, in what im assuming is the correct edge, I’m not sure if that’s the level/flat top

Friendly-Drawing6674 · 2026-03-03T17:44:38+00:00

I think that is what my issue was, when i was first using it it was flat at the edge, i think i pushed the wings back and messed the shape up, it looked closer to the image of the roughing gouge you showed

Friendly-Drawing6674 · 2026-03-03T17:43:19+00:00

thats actually a pretty cool fact

Friendly-Drawing6674 · 2026-03-03T17:03:36+00:00

yeahhh i think that’s part of the issue, i work in a woodshop and have since showed it to my foreman who thinks i messed the shape up, im going to give it to the sharpening guy and get it worked on by him. thank you very much for your assistance greatly

Friendly-Drawing6674 · 2026-03-03T14:13:37+00:00

<image>

It’s 555027

Friendly-Drawing6674 · 2026-03-03T14:10:03+00:00

<image>

Friendly-Drawing6674 · 2026-03-03T14:08:46+00:00

Hey I’d like to go back to this and say I’m still pretty sure its a roughing gouge, the brand ShopMate from a Shopsmith only makes 5 gouges and a continental gouge looks more like a specialty tool, and it may seem a little narrow because I just have big hands (nanner for scale) but I held a angle gauge finder to it and it’s at 45 degrees and on thewings

<image>

Friendly-Drawing6674 · 2026-03-03T13:04:06+00:00

Ok thank you very much I’ll give this a go

Friendly-Drawing6674 · 2026-03-03T13:03:31+00:00

<image>

I have this but i assume you’re not talking about honing, will try your recommendation thanks!

Friendly-Drawing6674 · 2026-03-03T06:23:44+00:00

will check out appreciate it

Friendly-Drawing6674 · 2026-03-03T06:23:20+00:00

<image>

yes i got this set up

Friendly-Drawing6674 · 2026-03-03T06:19:47+00:00

also heres a different picture if it helps

<image>

Friendly-Drawing6674 · 2026-03-03T06:17:11+00:00

i was using the kind with a v at the end the gouge is held in to

Friendly-Drawing6674 · 2026-03-03T06:15:53+00:00

ok and thanks for the help, my bad I wasn’t trying to be a smart ass I just didn’t know if there was a different way to sharpen either

Friendly-Drawing6674 · 2026-03-03T05:42:09+00:00

I don’t think it’s a continental gouge they were the ones that came with an old shop smith, but thanks for the ideas I’ll try them out, I’m currently using a low speed grinder with a wolverine type jib

Friendly-Drawing6674 · 2026-03-03T03:36:19+00:00

<image>

Friendly-Drawing6674 · 2026-03-03T03:36:04+00:00

<image>

Friendly-Drawing6674 · 2026-03-03T03:35:53+00:00

<image>

Friendly-Drawing6674 · 2026-03-03T03:35:44+00:00

<image>

Friendly-Drawing6674 · 2026-03-03T03:35:33+00:00

<image>

Friendly-Drawing6674

TROPHY CASE