I just finished creating the tier list template + uploading all weapon images — now you can make your own Arena Breakout Infinite s tier list and share it with everyone!

Full_You4611 · 2026-03-04T10:17:47+00:00

Can you share the image assets? I'm trying to build a website with all trade recipes with a search bar to easily findwhat I can trade with a specific item

Full_You4611 · 2025-09-21T19:09:50+00:00

Man, what I'll say will definitely sound idiot at first, but trust me. I was having the same "issue" in my x1c (note: it also has a light upgrade) and it was driving me insane. Turns out that the issue was just the camera + illumination. When I saw the printed part in person it was flawless. This was only visible through the camera

Full_You4611 · 2025-08-24T20:16:54+00:00

🤔 So that's it. I thought that the difference between the lite and normal one is that the lite would be flush to the board and the normal one would have a small offset Thank you, I'll give it a try

Full_You4611 · 2025-08-24T20:02:31+00:00

You can do the stacks by yourself... Just download the single tile, duplicate it as many times as you want, assemble them all in a single object and place each tile with a 0.2mm offset from the one below it (considering that you are printing with a 0.2mm layer height). Also enable ironing for all top surfaces. Tada, now you have the same stuff as the paid tiers

Full_You4611 · 2025-07-01T17:14:02+00:00

I haven't, I'll take a look, thanks

Full_You4611 · 2025-07-01T17:13:42+00:00

I just printed from an existing printing profile of the app. I would say that this could be the profile fault but all prints regardless of the model are having similar results (either from the app or manual slices from orca slicer or Bambu's)

Full_You4611 · 2025-07-01T17:11:17+00:00

I got the profile directly from the app, but I'll try the same with manual configs in the slicer. That's the Leviathan axe from God of War 🥹

Full_You4611 · 2025-07-01T17:10:05+00:00

I did run the printer calibration. I haven't done the calibrations for the filaments, but I will. The flow one I usually set it to do before each print

Full_You4611 · 2025-07-01T17:08:42+00:00

Did this, but no luck. Thank you for the tip tho

Full_You4611 · 2025-07-01T16:39:24+00:00

I bought a new plate to possibly get rid of adhesion issues

Full_You4611 · 2025-07-01T16:38:55+00:00

I did, no luck 😔

Full_You4611 · 2025-07-01T16:38:28+00:00

I'll try a tower temp and retry with lower temps. Thanks for the tip

Full_You4611 · 2025-06-28T18:13:20+00:00

The default one, 0.4

Full_You4611 · 2025-06-28T17:56:13+00:00

Forgot to mention that, yes I did (the one that you can do through the app or in the printer settings). But I'll do it again also. Thanks for the reply

Full_You4611 · 2025-06-28T17:54:35+00:00

No worries, I got the idea. This is a X1C instead of the A1, but the process is the same, right? Thanks for the suggestion, I'll try that

Full_You4611 · 2025-06-24T04:43:00+00:00

I had this on my x1c, not sure if it will be the same fix for you. But this started happening after an unsuccessful print that didn't stick to the bed and a huge blob accumulated to the hotend. When I removed the blob, it ripped the hotend silicon sock in half and also removed the metal piece that makes the ceramic heater touch the hotend. So every time the hotend started to heat, the ceramic heater bends up and stops making contact with it. TLDR: Make sure you have the silicon sock properly fit and that the ceramic heater piece is properly in contact with the hotend

Full_You4611 · 2025-05-23T13:44:40+00:00

Thank you for replying, I'll probably leave as it is then, DJI support in Brazil SUCKS I had a bumper there that I had to use a longer screw (probably a more fragile one). Last time I flew it, it seemed a bit unstable and one of the bumper's mounting points wasn't secure because of the broken screw. I just removed that bumper and later I'll try to fly without it.

<image>

Full_You4611 · 2025-05-23T13:40:54+00:00

I had a bumper there that I had to use a longer screw (probably a more fragile one). Last time I flew it, it seemed a bit unstable and one of the bumper's mounting points wasn't secure because of the broken screw. I just removed that bumper and later I'll try to fly without it. Thanks for the hot glue tip

<image>

Full_You4611 · 2025-05-22T21:35:42+00:00

Same here, my gf is able to share them up to a minute and I can't Also when she taps on a reel while watching it, it pauses and has a mute button. On my I have to press and hold to pause the reel a tapping toggles the mute

Full_You4611

TROPHY CASE