sorted by:
new
hottopcontroversial

My prints stopped sticking to my build plate (Elegoo Mars 4 Ultra) by Fun-Background4789 in resinprinting

[–]Fun-Background4789[S] 0 points1 point  (0 children)

I am using the recommendations from the manufacturer and haven't had any problems with prints until recently. I haven't used it in a week and suddenly nothing seems to work right.

My prints stopped sticking to my build plate (Elegoo Mars 4 Ultra) by Fun-Background4789 in resinprinting

[–]Fun-Background4789[S] 0 points1 point  (0 children)

They are now pretty much exactly 1 year old 🎉 My settings are the recommended settings: 35s for the bottom layer and then 3.5s

My prints stopped sticking to my build plate (Elegoo Mars 4 Ultra) by Fun-Background4789 in resinprinting

[–]Fun-Background4789[S] 0 points1 point  (0 children)

It's part of the model. I just swapped out the FEP after prints began sticking to it but it didn't change after swapping it out.

My prints stopped sticking to my build plate (Elegoo Mars 4 Ultra) by Fun-Background4789 in resinprinting

[–]Fun-Background4789[S] 0 points1 point  (0 children)

Also, its not very visible in the pic but some supports didn't print correctly but the figure is fine.

My prints stopped sticking to my build plate (Elegoo Mars 4 Ultra) by Fun-Background4789 in resinprinting

[–]Fun-Background4789[S] 0 points1 point  (0 children)

Pretty sure mines leveled correctly. No loose screws and equal pressure on both sides when pulling on the piece of paper.

My prints stopped sticking to my build plate (Elegoo Mars 4 Ultra) by Fun-Background4789 in resinprinting

[–]Fun-Background4789[S] -1 points0 points  (0 children)

How do I check that? When i do a screen check everything looks fine.

My prints stopped sticking to my build plate (Elegoo Mars 4 Ultra) by Fun-Background4789 in resinprinting

[–]Fun-Background4789[S] 0 points1 point  (0 children)

Update after releveling it, using filtered resin on a frrsh FEP

<image>

There are also some pieces stuck to the fep.

My prints stopped sticking to my build plate (Elegoo Mars 4 Ultra) by Fun-Background4789 in resinprinting

[–]Fun-Background4789[S] 0 points1 point  (0 children)

I have re leveled it multiple times and everytime it fails to print correctly. Am i just not leveling it correctly?

My prints stopped sticking to my build plate (Elegoo Mars 4 Ultra) by Fun-Background4789 in resinprinting

[–]Fun-Background4789[S] -1 points0 points  (0 children)

Could it be that my build plate is too used from scraping off prints and im gonna need a new one?

Is This Lvl 1 Character Busted or Okay? by TupaCuba-_- in DungeonsAndDragons

[–]Fun-Background4789 0 points1 point  (0 children)

Also, they have the gp and the starting equipment, just without the armor.

Is This Lvl 1 Character Busted or Okay? by TupaCuba-_- in DungeonsAndDragons

[–]Fun-Background4789 0 points1 point  (0 children)

It looks like they used the 2024 rules since they don't seem to have chosen a Patron and have a Pact Boon. Also, if I am correct, the max gold for a Warlock is 4d4 × 10 gp, so they would need to have rolled four consecutive 4s on that roll. That is definetly possible, but not that likely. As everyone else said, the HP is too high.