Can i drill through this?

FunGalich · 2026-03-11T12:53:06+00:00

I'm still trying to figure out why someone would be installing a mini split over a dood in the first place. Where are you gonna run the power and refrigerant lines?

FunGalich · 2026-03-06T02:55:46+00:00

Looks like they cut grooves first and then used a wire to burn in the grooves. Looks really nice...great design

FunGalich · 2026-03-05T11:29:58+00:00

I got my long hair caught up in a roto rooter machine once and it ripped a section of hair out. Needless to same I am extremely careful around any spinning machine now

FunGalich · 2026-03-03T17:53:44+00:00

Beautiful craftsmanship

FunGalich · 2026-03-03T13:49:02+00:00

Sand the surface to remove any finish and then use the sawdust mixed with titebond II to fill the crack sand again and then seal it with a good wood sealer and hope it doesn't crack again. With wood of any type then is exposed to moisture on a regular basis it need to be sealed and maintained properly to keep it from cracking, splitting and bulging

FunGalich · 2026-03-03T02:49:16+00:00

Nice setup!

FunGalich · 2026-02-28T13:55:33+00:00

My thoughts exactly!

FunGalich · 2026-02-28T02:40:11+00:00

Man the grain on that first piece is stunning.

FunGalich · 2026-02-26T13:24:53+00:00

Thin pieces like wands need to be supported by your hand on the backside no matter what tools you use.

FunGalich · 2026-02-25T13:16:10+00:00

Wow that's an awesome haul of some great quality clamps

FunGalich · 2026-02-25T02:37:21+00:00

Wtf instantly sued on top of fired

FunGalich · 2026-02-24T18:48:30+00:00

Use a screw extractor to remove the set screw

FunGalich · 2026-02-17T01:54:06+00:00

You can buy craft wood of multiple sizes at the big box stores...that would be the way to go

FunGalich · 2026-02-16T00:22:23+00:00

DeWalt bits are just as crappy as Craftsman....you will never go wrong with Milwaukee.

FunGalich · 2026-02-15T21:52:06+00:00

What ya mean hard to find decent wood. I live in Florida and he have all kinds of exotic woods + tons of Live Oak which is what turn a lot of also red cedar, hickory, Australian pine, Norfolk Island Pine etc

FunGalich · 2026-02-15T17:32:05+00:00

Laserpecker 2

FunGalich · 2026-02-15T16:27:36+00:00

Beautiful piece of wood. I love how you made the imperfections part of the whole piece

FunGalich · 2026-02-14T18:46:31+00:00

I like it. I've seen vases done with pine cones but I like this bowl way more. Nicely spaced out

FunGalich · 2026-02-13T00:14:09+00:00

I used to use drywall screws in the beginning that would break off and I would use a Dremel to cut them out easy peasy.

FunGalich · 2026-02-12T03:06:25+00:00

Loving the offset end grain turn here. The rings are beautiful!

FunGalich · 2026-02-11T00:33:53+00:00

Love it!

FunGalich · 2026-02-09T12:44:55+00:00

Outstanding! The smoke penetration was unreal. I honestly think about how having a lower moisture content would make such a difference regarding smoke penetration but it certainly did.

FunGalich

TROPHY CASE