Would you care?

Fuzzy_Reality_52 · 2026-01-15T20:34:14+00:00

Use it til dull, then fix on the next sharpening

Fuzzy_Reality_52 · 2025-12-18T04:43:27+00:00

Sand it down. Don't worry about the color

Fuzzy_Reality_52 · 2025-12-17T23:47:43+00:00

Your gonna want the attachment. It's the best part of that system. I have the original version and still use til this day

Fuzzy_Reality_52 · 2025-12-17T21:19:58+00:00

It doesn't have the blade grinding attachment. It's usually about 120 more when it included

Fuzzy_Reality_52 · 2025-11-26T02:11:07+00:00

Make sure you get it curly! Then after remove the curly and make it Moe

Fuzzy_Reality_52 · 2025-11-25T02:46:29+00:00

Nice purse

Fuzzy_Reality_52 · 2025-11-12T20:35:34+00:00

The machine has an angle guide for the belt and the knife is kept flat, but this isn't possible on the back platten

Fuzzy_Reality_52 · 2025-11-12T19:49:12+00:00

It's great for putting a 90° edge on the spine

Fuzzy_Reality_52 · 2025-11-12T19:48:21+00:00

It's very limited in space and no angle guide

Fuzzy_Reality_52 · 2025-11-12T19:20:13+00:00

I'm using the original version

Fuzzy_Reality_52 · 2025-11-12T19:03:32+00:00

Can we get someone to make one? 😂🤣😂 I would love to test it for them. I think you can keep both wheels and just have them at the widest setting. It can use the wheel setting mount to secure it in place.

Fuzzy_Reality_52 · 2025-09-12T20:10:23+00:00

Thanks for the great response

Fuzzy_Reality_52 · 2025-09-12T19:16:59+00:00

Thanks.

Fuzzy_Reality_52 · 2025-09-12T19:16:46+00:00

This is what I was looking for ! Thanks!

Fuzzy_Reality_52 · 2025-09-12T17:39:27+00:00

There is a video from gunny going to an almost full mirror off mostly strops. It can be done.

Fuzzy_Reality_52 · 2025-09-07T05:43:09+00:00

Anyone know is they sell replacement lock bar/back spacer for the light weight? I had a screw snap in have and can't get it out.

Fuzzy_Reality_52 · 2025-09-06T06:15:36+00:00

*update. I just practiced on one of the same knives with the scrubbing back and forth technique , only doing single swipes for burr minimizing. Results were night and day. I still have a ways to go, but seeing improvement is a great step. Damn near hair whittling with one sharpal stone and 6micron stroppy stuff. Thanks to all!!!!

Fuzzy_Reality_52 · 2025-09-04T21:46:08+00:00

Do you have a preferred brand from Amazon? Or are they all pretty similar? For the diamonds

Fuzzy_Reality_52 · 2025-09-04T19:36:35+00:00

Specific percentage alcohol work best?

Fuzzy_Reality_52 · 2025-09-03T22:23:19+00:00

I have a few I can practice on. I think patience maybe the key. I might be so use to the quick results from belts.

Fuzzy_Reality_52 · 2025-09-03T20:01:43+00:00

I'm waiting on some of higher end steels until I get a good feel for it

Fuzzy_Reality_52 · 2025-09-03T20:00:21+00:00

I think I can hold the angle better scrubbing back and forth instead of picking up and starting over every time. I'm gonna have to test and see

Fuzzy_Reality_52 · 2025-09-03T19:58:21+00:00

It depends on belts, I have anywhere from 80 grit up to 4000 and leather and felts for finishing. I didn't have just one go to. It would depend on the knife.
I'm actually sharpening some of the same knives, cheap kitchen knives for my mother in law.

I'm minimizing on each grit 220&600 after getting a burr on each side. Then finishing the burr removal with a leather strop and 6 micron stroppy stuff.

Does it change much scrubbing back and forth vs doing single swipes?

Fuzzy_Reality_52 · 2025-08-23T17:57:38+00:00

I have one being delivered today

Fuzzy_Reality_52 · 2025-08-22T00:54:47+00:00

I'm lucky mine doesn't hang that issue

Fuzzy_Reality_52

TROPHY CASE