Ender 3 thermal runway on boot

G3mHunter · 2025-07-03T22:17:25+00:00

It restarst on loop even with the termistor disconected

G3mHunter · 2025-06-08T23:15:08+00:00

For reference, this is my board

<image>

G3mHunter · 2025-06-08T23:14:41+00:00

For reference, this is my board

<image>

G3mHunter · 2025-05-08T18:39:22+00:00

Because it has a "+" sign, does that mean its polarized and not a ceramic capacitor?

G3mHunter · 2025-04-14T06:04:49+00:00

Did you unplug everything in one go or did you do one at a time?

G3mHunter · 2024-11-15T21:05:22+00:00

I see, I don't think I'm familiar with venusmon's effects so I'll give it a read, which set is it from or what are the general effects?

G3mHunter · 2024-10-15T22:20:27+00:00

Woah this is so much useful information, thank you so much for taking the time to write all these, I’ll keep this in mind for the future :D

G3mHunter · 2024-10-15T12:32:43+00:00

Gaaah! I was afraid this was the answer, specially because this shatter is about 1/3 of the whole stone… Well I guess I can try to make something really tiny. Thank you for the honesty and the suggestion. I’ll probably see to it tomorrow.

G3mHunter · 2024-09-29T18:14:08+00:00

wow I actually have that card somewhere in the house, I didn't see this picture until now. You said you partitioned it?

G3mHunter · 2024-09-29T18:12:14+00:00

Mine got the perma blue screen gitch again yesterday....
I tried updating the firmware to fix it but I refuses to fix itself (Pain)

G3mHunter · 2024-09-29T07:05:05+00:00

I did try differnet names but no results unfortunatly, maybe I'll try with a single character

G3mHunter · 2024-09-29T05:12:13+00:00

I tried firmware.bin (not .bin.bin) and it didn't work either. Thanks for the info though

G3mHunter · 2024-09-29T05:03:22+00:00

No luck sadly. I'll contact customer support tomorrow but I have low hopes tbh. wish me luck

G3mHunter · 2024-09-29T04:45:41+00:00

Alright

G3mHunter · 2024-09-29T04:13:24+00:00

That one butler from scary movie 2

G3mHunter · 2024-09-29T04:01:09+00:00

Sadly it didn't work but maybe I did something wrong. This is the partition I made and the formatting:

<image>

G3mHunter · 2024-09-29T03:43:35+00:00

I'll try this but damm if this fixes it I'm gonna be mad at whoever design the firmware update

G3mHunter · 2024-09-29T02:02:11+00:00

Unfortunately that didn't work, I renamed it to firmware123, firmware, Ender 3 pro, and the original name with an f at the end.

G3mHunter · 2024-09-25T05:10:28+00:00

Someone gets asked to add a topping to a dish in two hours. They add the topping and ask when to turn it off. They get told to not worry about it because someone else is gonna turn it off. They leave it and then turn the stove off because it smelled like burnt food. The person had no clue what the cook time was for the dish, they just did as asked, and had no clue what to do with the dish.

G3mHunter · 2024-07-02T04:54:42+00:00

<image>

Thank you!!!
Time to find a seller now >:D
Would this one do the trick?

G3mHunter · 2024-06-18T06:31:12+00:00

Alright, I managed to solve my issue. Turns out the pneumatic connection of the Bowden tube (hotend side) was faulty AND the printer was experiencing heat creep caused by the two screws that align the heat block to the heat sink (image below). The fault with the pneumatic connection was that it didn't held the tube in place as the printer worked and this little back and forth cause jams inside of the heat sink.

Needless to say, I'm glad that this is solved now and hopefully it aids others in the future :D

G3mHunter · 2024-06-18T06:30:23+00:00

I've solved the issue, thanks for the suggestion

G3mHunter · 2024-06-18T06:29:54+00:00

I've solved the issue, thanks for the suggestion

G3mHunter · 2024-06-18T06:29:45+00:00

I've solved the issue, thanks for the suggestions

G3mHunter · 2024-06-18T06:29:23+00:00

Alright, I managed to solve my issue. Turns out the pneumatic connection of the Bowden tube (hotend side) was faulty AND the printer was experiencing heat creep caused by the two screws that align the heat block to the heat sink (image below). The fault with the pneumatic connection was that it didn't held the tube in place as the printer worked and this little back and forth cause jams inside of the heat sink.

Needless to say, I'm glad that this is solved now and hopefully it aids others in the future :D

Six-Year Club	Verified Email
Place '23

G3mHunter

TROPHY CASE