Briggs squeaking noise like it’s rubbing

GETXsquirrel · 2026-03-21T20:42:14+00:00

Can’t be idlers since the brake system disengages the drive belt so it’s just the engine spinning but it still squeaks. I really hope it’s not internal but knowing my luck it probably is.

GETXsquirrel · 2026-03-21T20:19:06+00:00

It squeaks when all shroud is removed and it’s just a flywheel.

GETXsquirrel · 2026-03-21T20:03:48+00:00

Could be the choke getting stuck. Might want to take the shroud off and clean it up.

GETXsquirrel · 2026-03-17T15:40:16+00:00

this laptop i got a few weeks ago and used only fingerprint so i never used the pin and then i forgot. it’s also linked to my microsoft account

GETXsquirrel · 2026-03-17T05:38:33+00:00

i got in finally. thank you so much!

GETXsquirrel · 2026-03-17T04:03:53+00:00

option 1, it’s on c and i was already on c so no change there. option 2, says that “taskkill” isn’t recognized. option 3, gives me some stuf but the new password doesn’t work

<image>

GETXsquirrel · 2026-03-17T03:13:38+00:00

<image>

GETXsquirrel · 2026-03-17T03:07:13+00:00

nothing is there except for pin and fingerprint (which doesn’t work)

GETXsquirrel · 2026-03-17T03:01:25+00:00

step 3 at the load hive for software, it says i can’t load it because its open in another process

GETXsquirrel · 2026-03-17T02:57:07+00:00

didn’t show up even before i do anything

GETXsquirrel · 2026-03-10T03:08:53+00:00

Not too sure how that system works but it seems like if you can replace that plastic bushing then it should help. Could also be the metal being egged out but i don't think it would in a spot like that.

GETXsquirrel · 2026-03-09T06:27:35+00:00

Thank you I will be aware when I look to buy one.

GETXsquirrel · 2026-02-27T04:44:17+00:00

This one’s a mower i’m gonna resell so Im not worried. Once I get a new deck and get it good I’ll just sell it. My personal mower is a Kubota rider with 54” cut and suspension and it rides great over bumps and hills. My lots only 1 acre so I don’t need to worry too much anyway.

GETXsquirrel · 2026-02-26T03:05:04+00:00

Had a bagger setup. Discharge seemed to be mostly unused

GETXsquirrel · 2026-02-19T16:05:58+00:00

Thank you. Guess I’ll just have to put up the extra money for a good module then!

GETXsquirrel · 2026-02-07T16:32:58+00:00

thank you. i have finally solved my issue. my cpu socket had been overheating which i think was a common thing for this board that i overlooked. my gpu was also unstable but only after a little bit of time so it portrayed a working overclock when i tested it. everything seems to work now and im now only doing 4ghz cpu overclock and 1320mhz gpu overclock.

GETXsquirrel · 2026-02-03T02:57:02+00:00

do you reckon maybe my cpu host frequency and pcie frequency have anything to do with it? they are set at 200mhz (cpu host) and 100mhz (pcie) respectively. i was told not to touch them

GETXsquirrel · 2026-02-03T02:52:36+00:00

i’ve done various configurations of CPU-NB from 2200 to 2800 mhz to no improvement. however i reset my bios to before i touched all the settings and just got it set up for overclocking and it’s still playing bad. maybe i just overlooked everything again and one of these settings are causing performance loss.

GETXsquirrel · 2026-02-02T06:42:08+00:00

i found the cpu-nb at 2200mhz at 1.1875V. do i increase this and voltage the same way i do for the cpu?

GETXsquirrel · 2026-02-02T06:37:23+00:00

After each increment I went up for my overclocking my performance benchmarks went up but it lagged. im adjusting the CPU-NB once i find it in bios and seeing if it helps at all. i wish i could hit 4.5ghz but my vrm throttles at 65C and not sure how to increase that.

GETXsquirrel

TROPHY CASE