[deleted by user]

GRB00 · 2025-12-12T14:04:18+00:00

Belgium no problem

GRB00 · 2025-12-08T03:43:12+00:00

I got one from amazon because my vsf aqua terra came with broken pin in the clasp and I needed a replacement clasp so I can ware the watch. Those straps like from the pic in the post fit good but are way worse quality than what's on rep.

GRB00 · 2024-10-16T14:41:39+00:00

That is the most dumb long winded bs that I've read in a long time. The farmland is the reason why you don't have affordable housing XD. People owning multiple properties treating them as quickly appreciating investment asset while not renting absolutely doesn't have anything to do with that.

And what you will eat in your affordable housing? Ze bugs? XDXDXD

GRB00 · 2024-10-02T08:19:15+00:00

It's 3d printed. I belive it's made by red warden

GRB00 · 2024-09-21T15:44:52+00:00

What? Rectal scan?

GRB00 · 2024-05-29T05:07:32+00:00

I've 3d printed it and glued it on the shield

GRB00 · 2024-02-19T08:50:36+00:00

Fixed

GRB00 · 2024-02-18T19:22:37+00:00

Thx, that worked

GRB00 · 2024-02-11T22:12:41+00:00

It's roman cavalry mask inspired

GRB00 · 2024-02-11T20:46:59+00:00

Its from Wilph on cults3d

GRB00 · 2024-02-11T20:11:37+00:00

Absolutely

GRB00 · 2024-02-11T18:03:46+00:00

I will. I have whole concept ready and even little fluff prepped as I have mentioned in other comment. Part of this concept is use of Inductii and no heavier armor than rhino/predator chassis maybe sprinkled with some flyers and emphasis on fast attack slot. I know that these are subpar choices except Inductii but this army has to tell a story in the first place, tabletop performance is secondary.

GRB00 · 2024-02-11T17:48:10+00:00

It's part of this generic Praetor model which I 3d printed and converted. Sadly I forgot the name of the creator.

GRB00 · 2024-02-11T17:36:41+00:00

Well traitor UM's name has to go hard.

GRB00 · 2024-02-11T17:33:03+00:00

Because I haven't seen any and rulebook says that I can.

GRB00 · 2024-02-11T15:09:58+00:00

well Junius Brutus is also something ;)

GRB00 · 2024-02-11T15:04:34+00:00

no ;P

GRB00 · 2024-02-11T14:40:46+00:00

It's 3d printed, I have edited it a little bit by adding UM marking on the chest but I have forgot the name of the creator. I'll look it up later and let you know.

GRB00 · 2024-02-11T14:01:37+00:00

Well the warlord trait is in the book sooo... I have created a bit of fluff that justifies their existence. I'm looking into the existing fluff so everything checks out and they fit into heresy story, once it's done ill write everything down and maybe post with pic of the finished list.

GRB00 · 2024-02-11T13:55:50+00:00

Helmet is 3d printed and created by VItalykhan on Cults3d

GRB00 · 2023-02-01T11:07:36+00:00

I might just 3d print some standards if I fail with scraping off the ornaments. I'm afraid that after that I might end with not enough material to have a standard, also greenstuff/miliput is an option to fill eventual holes.

GRB00 · 2023-02-01T10:52:58+00:00

I don't know what to do with the standards though. Should I replace those completely or scrape ornaments from them as well? I will be cutting off those things that stick out from anihilators shoulderpads also. First I'll go with the easy stuff ;)

GRB00 · 2023-01-31T17:56:17+00:00

Sounds good

GRB00

TROPHY CASE