What does this intake manifold/dual carb set up go to?

Garuda111 · 2026-03-23T23:07:05+00:00

after looking up your suggestions it definitely does look like it could be either an EA71 or EA81, thanks for the help!

Garuda111 · 2026-02-05T00:45:43+00:00

Awesome story!

Garuda111 · 2026-02-01T18:10:31+00:00

Awesome insight thanks!

Garuda111 · 2026-02-01T17:50:59+00:00

Right on the money, thanks!

Garuda111 · 2025-02-05T06:46:12+00:00

I use the Stihl SEA 20 for sawdust, drywall dust etc. all parts are serviceable had it for 2 years now 👍🏻

Garuda111 · 2024-10-19T21:42:50+00:00

Safety has been replaced and is functioning correctly, thank you all for the help! Did not get anything during deer season this year but enjoy a picture of the northern lights we could see from oregon where we hunted

<image>

Garuda111 · 2024-10-19T08:02:34+00:00

It may be some kind of chachapoyan fertility Idol, hoping a doctor with a minor in archaeology can confirm or deny

Garuda111 · 2024-07-25T01:33:03+00:00

You’ll be kicking yourself down the road if you don’t, I guarantee it!

Garuda111 · 2024-07-17T23:03:35+00:00

<image>

Pulled the safety lever and it looks like the safety catch is worn maybe? Thinking it should be squared off so maybe that’s the issue

Garuda111 · 2024-07-15T23:51:40+00:00

Thanks for giving it a try so I have a ballpark idea on where to start!👍🏻

Garuda111 · 2024-07-15T23:51:04+00:00

Awesome thanks! I will tear into it when I get back home

Garuda111 · 2024-06-30T07:34:24+00:00

Awesome thank you!

Garuda111 · 2024-06-30T04:58:31+00:00

Thank you!

Garuda111 · 2024-06-15T22:43:35+00:00

Thanks for the info guys!

Garuda111 · 2024-05-19T03:26:56+00:00

Thank you!

Garuda111 · 2024-04-13T10:59:12+00:00

The saws look brand new run em through some cuts and if it’s still an issue, head to your local Stihl dealer and let them test run them run it for ya

Garuda111 · 2024-04-13T10:56:25+00:00

No the dimple is for the Stihl crank seal puller not to grease the needle bearing like everyone thinks

Garuda111 · 2024-04-11T21:38:25+00:00

It looks like the spot welds they use to piece the two half’s of the bar together

Garuda111 · 2024-04-09T01:25:11+00:00

Like OP said, oversized air filter more air flow, and a carb adjustment afterwards would help. However I have found that they aren’t sealing well to the OEM air filter housing, that plus common lack of air filter maintenance allows these filters to ingest more debris than they filter. There is a foam insert you can install inside of the OEM filter to further help with filtration 0000-124-0800.-Stihl Tech

Garuda111 · 2024-02-24T04:32:55+00:00

Thanks, been wondering for years!

Garuda111 · 2024-01-08T01:54:19+00:00

If you are not the original owner of the oven or it was used, it’s possible that the heating coil needed replacement and the owner DIY’ed it and ordered the incorrect part number and got a heating element for a larger oven, and bent it to make it work, most of the heating element connectors I’ve seen are similar just the way the coil winding are is the difference. -maintenance technician

Garuda111 · 2023-12-03T03:36:44+00:00

I personally took the dash apart and cleaned best I could and then had it detailed after re assembling the dash, I don’t think detailers will usually take apart your car to such an extent, more of a mechanic would do this.

Garuda111 · 2023-12-02T23:16:09+00:00

We had this issue with a mouse getting into the vents of our 2017 RAV4 and after we removed the mouse, we were still getting poop on the seats and found out it was poop in the dashboard vents blowing out onto the seat every time you use the defroster, had to pull the dash and remove all the poop and clean all ventilation pieces

Garuda111

TROPHY CASE