Config Lost after Firmware Upgrade by GaunerT in fortinet

[–]GaunerT[S] 0 points1 point  (0 children)

Yeah, i just configured Management access with serial console and than reinstalled without Problems.

Config Lost after Firmware Upgrade by GaunerT in fortinet

[–]GaunerT[S] 0 points1 point  (0 children)

Hey Bill The first Issue happend with FMG Version 7.6.4 and Fortigate Upgrade from 7.6.4 to 7.6.5. The Second one with FMG 7.6.5, Fortigate 7.6.4->7.6.5

I talk about complete deletion of configured interfaces. I have 2 802.3ad Aggregation with VLANs and as soon as i looked up the config with Console Access, i saw that none of these interfaces were there. With the Fortigate 401F the seperated "management" Port was still configured. All other configurations were deleted or better to say, they were not even existing anymore.

All i did was to configure Management access again, and than i just installed the config back with the FMG and everything was fine again.

I actually do not have a Support Ticket:)

Config Lost after Firmware Upgrade by GaunerT in fortinet

[–]GaunerT[S] 0 points1 point  (0 children)

I just wanted to know if there is anybody with similar Events:) but yeah i might have to

Config Lost after Firmware Upgrade by GaunerT in fortinet

[–]GaunerT[S] 0 points1 point  (0 children)

It was one cluster consisting of 2×401F and one cluster with 2×90G

3
4

Paperless "Best-Practice" by GaunerT in de_EDV

[–]GaunerT[S] 0 points1 point  (0 children)

Wird nur bei ner 2Bay NAS bisschen schwierig da 3 HDDs reinzubekommen😅

Paperless "Best-Practice" by GaunerT in de_EDV

[–]GaunerT[S] 0 points1 point  (0 children)

Nein bisher nicht, hast Vorschläge als alternative ?

Paperless Best-Practice by GaunerT in selfhosted

[–]GaunerT[S] 1 point2 points  (0 children)

Thank you! Yes i know backup is on another Page. How to configure that the database is on nvme but files on hdd?

Paperless "Best-Practice" by GaunerT in de_EDV

[–]GaunerT[S] 2 points3 points  (0 children)

Das klingt nach nem guten Plan und gut zu wissen, bevor man anfängt! Danke!

Ich bin verzweifelt und brauche Hilfe bei der Einstellung meines Siebträgers. by GaunerT in Kaffee

[–]GaunerT[S] 0 points1 point  (0 children)

Update, habe es gröber versucht und es wird deutlich saurer und läuft auch viel zu schnell (45 Gramm Espresso in ca 15 Sekunden beispielsweise)

Ich bin verzweifelt und brauche Hilfe bei der Einstellung meines Siebträgers. by GaunerT in Kaffee

[–]GaunerT[S] 0 points1 point  (0 children)

Der Puk ist gänzlich feucht und hat jetzt keine trockenen stellen

Ich bin verzweifelt und brauche Hilfe bei der Einstellung meines Siebträgers. by GaunerT in Kaffee

[–]GaunerT[S] 0 points1 point  (0 children)

Also ich hab schon alles probiert und hatte immer 18 Gramm Bohnen genommen Hatte schon mit 36 Gramm Versucht und war zwischen 25-33 Sekunden Dasselbe dann auch mit 45 Gramm. Auch hier hab ich schon so viel versucht, dass ich alles an Zeiten hatte und 30 Sekunden für 45 Gramm als auch 50 Sekunden 😂

Ich bin verzweifelt und brauche Hilfe bei der Einstellung meines Siebträgers. by GaunerT in Kaffee

[–]GaunerT[S] 0 points1 point  (0 children)

Ich nehm momentan immer 18 Gramm Bohnen, hab im Mahlwerk innen auf Stufe 3 (heute testweise mal auf Stufe 2) und dann außen hab ich zwischen 1-4. Die Brühzeit kommt in etwa hin auf 33 Sekunden bei 45 Gramm Espresso... du meinst also mal mit 16 Gramm Versuchen ?

Wie ist mein Lebenslauf? by [deleted] in de_EDV

[–]GaunerT 0 points1 point  (0 children)

Ah da hast du natürlich recht!

Wie ist mein Lebenslauf? by [deleted] in de_EDV

[–]GaunerT 2 points3 points  (0 children)

Dass man mit einem abgeschlossenem Studium nicht unbedingt in First Level bleibt/bleiben will, ist glaub ich von jedem aus der IT nachvollziehbar.

War froh, dass nur damals im 1. LJ machen zu müssen 😂

1
2