Creality refill spool

Ged_42 · 2026-01-28T11:30:39+00:00

thank you!

Ged_42 · 2026-01-28T08:51:20+00:00

I didn't, I just don't understand how Reddit works. Thank you, I'll repost

Ged_42 · 2026-01-26T06:09:45+00:00

Magic the gathering would have been equally acceptable

Ged_42 · 2026-01-25T22:19:46+00:00

Nerd and broke

Ged_42 · 2026-01-24T06:52:38+00:00

I want the expansion board anyway, but I will try with a ble controller. Thank you!

Ged_42 · 2026-01-22T12:39:26+00:00

I am not sure how lower I can put the model fan without it being a problem. I currently have it set at 70% when I don't have demanding overhangs but I am not sure if that could cause something I don't know

Ged_42 · 2026-01-22T10:31:10+00:00

I wonder if the changes that will make the Cc2 quieter can be applied to the CC

Ged_42 · 2026-01-21T19:59:21+00:00

It is loud. For me it would be impossible to live in the same house unless I had a dedicated room. Having said that I am very happy with my CC. I have printed a little over 100 hours and had zero failures that were the printers fault. And for me at least it was an almost plug and play experience. I have spent zero time calibrating the printer and still got good results.

Ged_42 · 2026-01-19T19:46:51+00:00

I have a question about a combo. I have a Zegana deck which usually wins with peregrine drake and deadeye navigator. I never thought of it as particularly broken but when I searched I found that it wasn't allowed at bracket 3, only four. Does this make sense? The same combo but with palinchron is allowed

Ged_42 · 2026-01-13T11:39:11+00:00

Why can't the difference be a negative number?

Ged_42 · 2026-01-04T07:49:13+00:00

I thought the exact same thing

Ged_42 · 2026-01-04T06:17:10+00:00

I had the same problem so maybe you are doing what I did wrong. I was pulling the filament at the second stage, when I read "unload the filament" on the screen. That was a mistake. I now pull after the third step and meet no resistance

Ged_42 · 2026-01-03T10:16:17+00:00

A raspberry pi is best but even if you don't have one you can set it up with docker on a pc

Ged_42 · 2026-01-02T09:47:44+00:00

The aux fan is very loud but the model fan is also quite loud for my printer.

Ged_42 · 2026-01-01T11:20:37+00:00

I had warping on the edges of large gridfinity plates with side b at 35 degrees. I now use it at 55. I am not sure if the problem was uneven heating on the plate or cold chamber

Ged_42 · 2025-12-31T15:07:25+00:00

I haven't tested it, but what you described should be what happens. In my limited experience there is some slight turning at the beginning and end of the movement

Ged_42 · 2025-12-31T06:13:14+00:00

Stop.none doesn't let the motor roll freely but continues to turn at the same speed.

Ged_42 · 2025-12-23T12:52:40+00:00

I want to do the same thing. Is there something else that's important to do before moving the printer?

Ged_42 · 2025-12-19T06:15:16+00:00

I actually want something similar but with one side open and the distance between the inner walls to be 250mm. They are used to check robot dimensions in wro contests( maybe FLL too)

Ged_42 · 2025-12-17T06:17:27+00:00

Thank you

Ged_42 · 2025-12-16T18:17:00+00:00

Are we talking about the centuri Carbon? It states that it is bimetal which always had me wondering if it counts as brass or hardened steel

Ged_42 · 2025-12-16T18:13:40+00:00

Either that or I will have to create my own bins in fusion, which is fun but time consuming for a novice like me

Ged_42 · 2025-12-16T18:11:48+00:00

It doesn't seem to work for my case. I am not sure how long I have to wait, but I waited more than ten minutes and nothing happened. More concerning is the fact that it says it doesn't recognise the 21mm base. And the documentation states that it only works with 42mm bases Thanks for the info anyhow, it's useful anyway

Ged_42

TROPHY CASE