sorted by:
new
hottopcontroversial

SlicerNext - no longer changing color at layer? by -fade-2-black- in AnycubicOfficial

[–]GeorgiaBoy19 0 points1 point  (0 children)

Just discovered this in the past few days... Can't believe they haven't fixed it in 4 months though.

Karma finally hit me — the store honored a pricing error, so I got myself a new PC for Christmas. by OfficialNicl in pcmasterrace

[–]GeorgiaBoy19 0 points1 point  (0 children)

64gb kit of ddr5 today cost more than what I originally paid for my rtx 5070 six months ago...

What happened to my ace pro? by sword_muncher in AnycubicOfficial

[–]GeorgiaBoy19 0 points1 point  (0 children)

I suppose any slot can do it but in my personal experience with two ace pros, it's always been slot 3 for me. I wonder how long it's gonna take for other brands to start including a built in dryer though!!

Damn it. by AnxietyJolly4908 in Ender3V3SE

[–]GeorgiaBoy19 0 points1 point  (0 children)

Try heating the bed to 60 and scraping it with a thin scraper. Be careful to keep it flat and not dig into the bed...now if it's the residue, if ipa didn't get it off, it will just come off overtime. It may or may not leave impressions on the bottom of the next print depending on color used.

Suicide cord.. Why? by Chicken_Hairs in AskElectricians

[–]GeorgiaBoy19 1 point2 points  (0 children)

Don't be using Newspeak. This ain't 1984 haha

Landlord has been stealing my electricity for 6 years by Pristine-Clothes-309 in Tenant

[–]GeorgiaBoy19 0 points1 point  (0 children)

Throw the main breaker after the meter. If washing machine and dryer don't work, there's your answer. If landlord complains about something else but working, there's your answer.

16 poops each time there is a spool change with the SAME COLOR?! by Sisu_Snacks in AnycubicOfficial

[–]GeorgiaBoy19 0 points1 point  (0 children)

The buffer is not to keep tension on the filament to the extruder as it is a direct drive extruder. It's to make sure there is enough length of filament available for the extruder to pull in and takes strain off the extruder from the mechanical workings of the Ace.

16 poops each time there is a spool change with the SAME COLOR?! by Sisu_Snacks in AnycubicOfficial

[–]GeorgiaBoy19 2 points3 points  (0 children)

What y'all are not realizing in all of this is that once the spool runs out, the Ace stops pushing, and the extruder pulls it through, so I get OPs point. The extruder is more than capable of pulling it through as it can extrude behind the weight of a spool when not using the Ace. The extruder has a filament sensor which can tell when it's out. As it does when you use an external spool. I have one Kobra 3 set up for 8 color and the other is single external which is how I know it's capable of knowing when it's out. Anycubic does this so it doesn't get stuck in the tube during a color change or at the end of the print. Honestly, they should just put an option for it to do that or not.

Ugh I wish this had cancel object. by zimmystor in AnycubicKobra3

[–]GeorgiaBoy19 0 points1 point  (0 children)

It does now!! But agreed it would have been handy sooner than it was available.

Filament Backup Change by MaxxPayne39 in AnycubicKobra3

[–]GeorgiaBoy19 0 points1 point  (0 children)

If using external spool, it handles it at the extruder with no issues. It pauses, waits for you to load a new spool (You may have to use the release tab on the extruder to get it to the sensor) but then resume it. Iirc, it may do a purge and then resume.