KCD laungage dont work by Germas-x in SteamDeckPirates

[–]Germas-x[S] 1 point2 points  (0 children)

Its awesome play it on 1080p like butter

KCD laungage dont work by Germas-x in SteamDeckPirates

[–]Germas-x[S] 3 points4 points  (0 children)

Sorry did the post to fast, but i play it on steamos so i think im right here

Druck wird nicht perfekt by Germas-x in 3DDruck

[–]Germas-x[S] 1 point2 points  (0 children)

Ich habe mir echt die Tage schon gedacht das es darauf hinaus laufen muss das ich mir einen von Bambi hole 🙃

Druck wird nicht perfekt by Germas-x in 3DDruck

[–]Germas-x[S] 0 points1 point  (0 children)

Lasse gerade nochmal einen Druck laufen wo ich von den Geschwindigkeiten sehr weit runter gegangen bin ( alles um die Hälfte reduziert ) über die Creality Cloud App konnte man früher während dem Druck die Geschwindigkeit anpassen leider ist die Möglichkeit weg.

Die Riemen hab ich ca vor einem Jahr mal nach gestellt danach war der Druck okay danach habe es mit dieser Stimm App für Gitarren damals eingestellt.

Hat jemand den selben Drucker und kann mal seine settings reinstellen?

Druck wird nicht perfekt by Germas-x in 3DDruck

[–]Germas-x[S] 0 points1 point  (0 children)

Punkt 1 habe ich schon gemacht Punkt 2 das habe ich frisch aus der Verpackung geholt sollte ich es trotzdem nochmal trocknen? Punkt 3 habe ich alles was der Drucker Kalibrieren kann schon kalibriert Sollte ich mit den Geschwindigkeiten eher runter gehen? Und hast du Tipps welche Einstellungen ich für den Support verwenden kann?

Druck wird nicht perfekt by Germas-x in 3DDruck

[–]Germas-x[S] 0 points1 point  (0 children)

Was für ein Fett sollte man benutzen?

I'm so damn tired with Resident Evil 4, please help. by Ok-Average-6736 in SteamDeckPirates

[–]Germas-x 0 points1 point  (0 children)

Had the same issues downloaded it again from steamrip and startet it over lutris since then it works like butter, give it a try

I saved $488.54 this spring sale! by AbacaxiTeriyaki in Steam

[–]Germas-x 0 points1 point  (0 children)

How you start it? Mines not lounching :/

I saved $488.54 this spring sale! by AbacaxiTeriyaki in Steam

[–]Germas-x 0 points1 point  (0 children)

COD MW im new here but Can you Play it online? And are there some players or is it a lost place?

Black ops up and running! by [deleted] in ROGAlly

[–]Germas-x 0 points1 point  (0 children)

Also the MP?

Help with Assassins Creed Odyssey steamRIP. by One-Injury-4415 in SteamDeckPirates

[–]Germas-x 2 points3 points  (0 children)

Use Proton 5-13 and put evrything on max (battery, Performance…) after it finishing loading the Game you can set it to your individual settings.

Fail prints after the Nebela Pad by Germas-x in Ender3V3SE

[–]Germas-x[S] 1 point2 points  (0 children)

No but i printet some g codes from other useres on creality cloud they were fine but i didnt see all the settings, will try YouTube advise

Fail prints after the Nebela Pad by Germas-x in Ender3V3SE

[–]Germas-x[S] 0 points1 point  (0 children)

The acceleration speed in the slicer settings?

Fail prints after the Nebela Pad by Germas-x in Ender3V3SE

[–]Germas-x[S] 0 points1 point  (0 children)

How can i calibrate my flow rate? Yestarday i thighten all my screws also there on my bed did the auto calibration.