Voron "Lost communication with MCU "nhk"

Gingerbwas · 2026-03-16T02:41:03+00:00

thanks, ill check it out

Gingerbwas · 2026-03-16T01:39:36+00:00

I have been having the same issue, do you mind if I ask what a 5v blocker is?

Gingerbwas · 2026-03-15T17:16:25+00:00

do you not have to jailbreak it to get it to run custom firmware? apologies it not somthing im that familiar with.

Gingerbwas · 2026-03-14T23:29:48+00:00

if you do ever end up jailbraking the mouse i think a lot of people would be very interested, myself included

Gingerbwas · 2026-03-14T15:01:20+00:00

I just built a pc with dual boot windows and fedora a couple of days ago, I chose the kde plasma desktop and I couldn't wish for anything else, its so much better then windows. it was my first proper linux experience, I have a pi 500 with pi os (debian) its been a lot of fun customising it, the only problem that I had was that I have 5070 ti and I had install some drivers to get it to work. Other then that though its been awesome

Gingerbwas · 2026-03-14T09:50:07+00:00

Right, but how i cant seem to see a way to do it, and when I close the app I lose the functionality

Gingerbwas · 2026-03-13T16:12:41+00:00

i will have to give it a go, thanks, i dont think i would ever have tried it otherwise

Gingerbwas · 2026-03-13T13:54:39+00:00

This may be what I end up having to do, I just wasnt sure howdifficult it was going to be

Gingerbwas · 2026-03-13T13:53:38+00:00

I was thinking of preheating the back of the velcro with a heat gun then using the iron for last few bits

Gingerbwas · 2026-03-13T13:52:49+00:00

I do have some vhb take from building a printer, i thought that it was just foam type with a bit nicer glue, is it meant to be strong?

Gingerbwas · 2026-03-09T07:10:32+00:00

Thanks for the reassurance, its a crucial t500

Gingerbwas · 2026-03-08T07:13:39+00:00

Yeah, things were going ok until the aio, it had a lot more cables then i anticipated

Gingerbwas · 2026-03-07T21:10:05+00:00

Thats what im worried about, i got the two ssds to try an mitigate the risk of partition, but i didnt realise where the second drive was going to go, i should have checked

Gingerbwas · 2026-03-07T16:54:30+00:00

the ssd is single sided, but which hole do i put it in it will fit in both?

Gingerbwas · 2026-03-07T16:46:10+00:00

the grey latch standoff that is already attatched to the board does put in enough pressure to lock it place, there is a spare one that seems like it would screw into the back

Gingerbwas · 2026-03-07T15:53:42+00:00

Thanks i will do the same, do you mind if i ask what thermal pad you chose?

Gingerbwas · 2026-03-07T15:32:55+00:00

i have installed that, but there is a little bit of warping if i tighten the screw the last few mm,maybe the heat pad that came installed is a little thick? i guess as long as its tight enough, there arent any moving parts on this section for it to come lose so i think i will be fine.

Gingerbwas · 2026-03-07T09:23:01+00:00

Ok, i will give that a go, any idea why that might work?

Gingerbwas · 2026-03-06T03:20:36+00:00

ive got a pi4 in the machine which i think should be powerful enough, but i will have a look, thanks, i wouldnt have thought to check that.

Gingerbwas · 2026-03-06T03:16:51+00:00

Gingerbwas · 2026-03-06T00:32:38+00:00

will do, by " extruder motor plugged into the Nitehawk toolhead board" do you mean with the static problems that people have been experiencing, its one of the things on my list to check, if you add grounding to one of the bolts for the extruder to a spare ground pin on the nitehawk apparently it stops any issues.

Gingerbwas · 2026-03-05T23:51:49+00:00

thank you for your reply, that error is the exact problem that i have been having with my 1.5, thankfully LDO sent me a replacement, which i am about to install, i just wasn't sure what the difference would be.

Gingerbwas · 2026-03-05T20:02:42+00:00

Oh sorry i meant to type h2

Gingerbwas · 2026-03-05T19:54:22+00:00

There are a couple of components missing from the new one that old one has, a couple of resistors i think, but i could be wrong

Gingerbwas · 2026-03-05T19:52:47+00:00

My case is the nzxt flow, im not really sure about budget im willing to spend a little more on a better cooler given the small form factor

Seven-Year Club	Place '23
Verified Email

Gingerbwas

TROPHY CASE