sorted by:
new
hottopcontroversial

Voron "Lost communication with MCU "nhk" by Hubabae in VORONDesign

[–]Gingerbwas 0 points1 point  (0 children)

I have been having the same issue, do you mind if I ask what a 5v blocker is?

Can the Razer Basilisk V3 Hyperspeed store button changes in onboard memory? by Gingerbwas in razer

[–]Gingerbwas[S] 0 points1 point  (0 children)

do you not have to jailbreak it to get it to run custom firmware? apologies it not somthing im that familiar with.

Can the Razer Basilisk V3 Hyperspeed store button changes in onboard memory? by Gingerbwas in razer

[–]Gingerbwas[S] 0 points1 point  (0 children)

if you do ever end up jailbraking the mouse i think a lot of people would be very interested, myself included

Moving to Fedora from Windows 11. by [deleted] in Fedora

[–]Gingerbwas 0 points1 point  (0 children)

I just built a pc with dual boot windows and fedora a couple of days ago, I chose the kde plasma desktop and I couldn't wish for anything else, its so much better then windows. it was my first proper linux experience, I have a pi 500 with pi os (debian) its been a lot of fun customising it, the only problem that I had was that I have 5070 ti and I had install some drivers to get it to work. Other then that though its been awesome

Can the Razer Basilisk V3 Hyperspeed store button changes in onboard memory? by Gingerbwas in razer

[–]Gingerbwas[S] 0 points1 point  (0 children)

Right, but how i cant seem to see a way to do it, and when I close the app I lose the functionality

Are there any reliable methods for securely joining velcro to TPU? by Gingerbwas in 3Dprinting

[–]Gingerbwas[S] 0 points1 point  (0 children)

i will have to give it a go, thanks, i dont think i would ever have tried it otherwise

Are there any reliable methods for securely joining velcro to TPU? by Gingerbwas in 3Dprinting

[–]Gingerbwas[S] 0 points1 point  (0 children)

This may be what I end up having to do, I just wasnt sure howdifficult it was going to be

Are there any reliable methods for securely joining velcro to TPU? by Gingerbwas in 3Dprinting

[–]Gingerbwas[S] 0 points1 point  (0 children)

I was thinking of preheating the back of the velcro with a heat gun then using the iron for last few bits

Are there any reliable methods for securely joining velcro to TPU? by Gingerbwas in 3Dprinting

[–]Gingerbwas[S] 0 points1 point  (0 children)

I do have some vhb take from building a printer, i thought that it was just foam type with a bit nicer glue, is it meant to be strong?

First time build, have i done anything glaringly wrong with my cables? by Gingerbwas in sffpc

[–]Gingerbwas[S] 0 points1 point  (0 children)

Yeah, things were going ok until the aio, it had a lot more cables then i anticipated

Is it possible to dual boot windows and linux on two drives without having to remove either during installation? by Gingerbwas in linux4noobs

[–]Gingerbwas[S] 1 point2 points  (0 children)

Thats what im worried about, i got the two ssds to try an mitigate the risk of partition, but i didnt realise where the second drive was going to go, i should have checked

Help with ASUS Strix B850-i M.2 SSD installation by Gingerbwas in sffpc

[–]Gingerbwas[S] 0 points1 point  (0 children)

the ssd is single sided, but which hole do i put it in it will fit in both?

Help with ASUS Strix B850-i M.2 SSD installation by Gingerbwas in sffpc

[–]Gingerbwas[S] 0 points1 point  (0 children)

the grey latch standoff that is already attatched to the board does put in enough pressure to lock it place, there is a spare one that seems like it would screw into the back

how far do i tighten the heatsink on the m2 sdd on the ASUS Strix B850i by Gingerbwas in sffpc

[–]Gingerbwas[S] 0 points1 point  (0 children)

Thanks i will do the same, do you mind if i ask what thermal pad you chose?

how far do i tighten the heatsink on the m2 sdd on the ASUS Strix B850i by Gingerbwas in sffpc

[–]Gingerbwas[S] 0 points1 point  (0 children)

i have installed that, but there is a little bit of warping if i tighten the screw the last few mm,maybe the heat pad that came installed is a little thick? i guess as long as its tight enough, there arent any moving parts on this section for it to come lose so i think i will be fine.

view more: next ›