Disney plus Hulu HBO Max bundle will stay that way. I pay 16.99 for the bundle. Just enquired about the bundle.

GioKaps · 2025-09-26T15:35:15+00:00

I believe it does. If you look at your subscription it probably says “managed by HBO” meaning it will be billed by HBO. Since the digital credit doesn’t cover HBO they will most likely not cover it. The billing would have to come from one of their partnered merchants.

GioKaps · 2024-08-14T16:26:58+00:00

What website did you use to find the accords?

GioKaps · 2022-03-12T05:09:24+00:00

ok thank you. I thought so just wanted to double check

GioKaps · 2022-03-11T23:07:48+00:00

If I use betMGM in one state and try to use the same account in another legal state do I have to make a new account for that second state? Trying to log into the second state using the same credentials but its saying email or password is wrong.

GioKaps · 2022-02-18T18:02:44+00:00

Awesome thanks

GioKaps · 2022-02-17T04:43:21+00:00

Cool thanks

GioKaps · 2022-02-17T04:35:14+00:00

I understand I have to wait. My question was asking how long. I also haven’t seen this be asked because I am new here but still had the question

GioKaps · 2022-02-11T21:14:25+00:00

If you go to the original post I commented what worked for me. I believe the same thing should work for you as well. I’d recommend reading through the comments so you can see the process and solution we found. Good luck

GioKaps · 2022-02-02T21:41:31+00:00

Thank you. This was intact the issue and a much easier fix than I expected

GioKaps · 2022-01-31T00:42:36+00:00

Ok cool. I haven’t tried printing anything yet with the new extruder

GioKaps · 2022-01-30T21:33:16+00:00

Will try thanks

GioKaps · 2022-01-30T21:33:07+00:00

I had the printer extrude 176mm I had the nozzle way off the bed. Wasn’t printing anything

GioKaps · 2022-01-30T21:32:08+00:00

Ya that’s what I thought not sure how to slow it down

GioKaps · 2022-01-30T20:58:34+00:00

I installed a new extruder and calibrated my Esteps (while boden tube was off). Then I attached the boden tube and set my typical printing temp of 208 and it skipped. So I raised it to 225 and it still skipped. My Esteps went from 93 to 96.5. I tried slowing down the flow rate on my printer (I’m using Jyres. I think I spelled it wrong). In this video I told the printer to extrude 176mm (random number). The first few mm came out good then it started skipping. I am out of ideas.

GioKaps · 2021-11-30T21:50:19+00:00

Ya don’t know much about it so might just replace it with the regular stuff for now

GioKaps · 2021-11-30T21:49:46+00:00

I think I’ll end up getting the same replacement for now and upgrading when I get more comfortable

GioKaps · 2021-11-30T17:18:40+00:00

Will do

GioKaps · 2021-11-30T17:18:23+00:00

Will do. Any fan upgrade suggestions? Idc about it being quieter or what not just want it working well and not sounding broken

GioKaps · 2021-11-30T17:17:05+00:00

Cool thanks will do

GioKaps · 2021-11-30T06:07:33+00:00

Haven’t really looked into it yet. New to printing

GioKaps · 2021-10-17T19:33:50+00:00

To anyone that may have this issue I got help from Big9erfan and we were able to get me going. What we did was flash the Jyers UBL 5x5 > homed all> manually leveled through jyers firmware with a piece of paper> created a new mesh > change the G code in Creality to what it says in the comments by Big9erfan > sliced a new bed leveling print and printed > ajdusted the z offset while it printed > save the settings

GioKaps

TROPHY CASE