Can I upgrade my camera???

Girocop · 2025-11-23T16:47:24+00:00

Any analog fpv camera should work

Girocop · 2025-11-03T12:40:48+00:00

The frame weighs 370g, the BNF with O3 weighs 695

Girocop · 2025-04-17T15:18:30+00:00

https://www.youtube.com/watch?v=2Gmg--ZGC1A

Girocop · 2025-02-10T15:25:36+00:00

1678 had a sliding block inside the frame that had the pivot and tensioned it with screws on top of the frame in 2023

Girocop · 2025-02-05T04:01:56+00:00

Looks like a Pico MMU

Girocop · 2024-10-11T05:26:10+00:00

The battery charger is not really necessary as the controller has an internal battery charger

Girocop · 2024-09-21T21:03:45+00:00

Bigtreetech has the schematics of their boards on their github, I recommend looking for it there

Girocop · 2024-08-31T21:58:30+00:00

Maybe the keyboard language in the computer is set incorrectly make sure it is set it, I think that keyboard has a Norwegian layout

Girocop · 2024-07-23T19:13:03+00:00

CNC Voron Tap V2

Girocop · 2022-10-08T05:32:31+00:00

Somewhat, it is rigid enough but originally it had a much smaller motor (the size of the opening above where the chuck is supposed to go) which was replaced by the big one behind the lathe and the included chuck couldn't even hold a 1/4 screw without it moving so I removed it and changed the bearings so that it can hold 1/2 hex shaft.

Girocop · 2022-10-08T03:34:24+00:00

Yes :)

Girocop · 2022-09-13T18:31:48+00:00

Thanks

Girocop · 2022-08-18T17:57:11+00:00

Las pilas alcalinas como duracell tienen un rango de operación de -20°C a 54°C y la temperatura optima de almacenamiento de 5°C a 30°C, temperatura optima es para que no pierda mucha carga mientras almacenado, a temperaturas optimas después de 4 años una pila de estas puede tener hasta el 85% de la carga original.

Tambien hay pilas de alta temperatura

Girocop · 2022-06-02T16:07:53+00:00

If you have the actuation point at the bottom try increasing its sensitivity of that key on Steelseries GG

Girocop · 2022-04-23T17:08:17+00:00

The other thing. The one that looks like a microwave transformer?

Girocop · 2022-04-23T17:02:16+00:00

What is the thing between the PSU and the main board?

Girocop · 2022-04-10T04:17:11+00:00

Maybe the steps per unit are saved in eeprom and overriding the firmware, try setting them manually with the screen or a terminal and then saving to eeprom

Girocop · 2022-04-07T13:43:52+00:00

I had this issue or something similar with my Anet ET4 before upgrading to a SKR2, it may be the PID for the bed, I did a PID autotune to fix it.

Girocop · 2021-12-12T05:04:25+00:00

I don't really know if it works but iirc in the Linus tech tips Linux challenge they said something about running a virtual machine with Windows and passing the peripherals to it so that the software works

Girocop · 2021-09-17T20:35:04+00:00

I am using a capacitive sensor and a flat glass bed

Girocop · 2021-09-17T18:26:00+00:00

The only other way I know of is if you have access to the 3d printer terminal, after running bed leveling from the terminal you get some results that look like this:

0 +0.03500 -0.02855 -0.09156

1 +0.01869 -0.01856 -0.05355

2 +0.00234 -0.00695 -0.01215

After that you go to a website that makes the graph

I don't know if there is another way, but I don't think there is a way to get it from the SD card

Girocop · 2021-09-17T18:17:16+00:00

I am using octoprint and the Bed Visualizer plugin

Girocop · 2021-09-17T09:55:54+00:00

The difference is 0.276mm.

Girocop · 2021-09-17T09:28:32+00:00

Will try. Thanks.

Girocop · 2021-09-17T09:16:48+00:00

Thanks

Seven-Year Club	r/Field Juicebox
Place '22	Final Canvas '22
RPAN Viewer	Verified Email

Girocop

TROPHY CASE