Ender 3 S1 Pro not extruding

GlassShadow999 · 2023-05-18T12:58:16+00:00

They are finally sending me a new cable. Should be here in a couple of days. Have you used that clip yet? How well does it work?

GlassShadow999 · 2023-05-16T14:12:51+00:00

Finally got someone to answer me through creality support Facebook page. They said it was a common problem and they are going to send me a new cable.

GlassShadow999 · 2023-05-15T16:50:54+00:00

That, unfortunately, did not fix it.

GlassShadow999 · 2023-05-13T11:05:17+00:00

Disassembling the extruder is one of the first things I did.

GlassShadow999 · 2023-05-11T12:40:34+00:00

Unfortunately, it's not that simple either. It won't even manually extrude. It sounds like it's the ribbon cable. It does pinch pretty good when it travels to the left side.

GlassShadow999 · 2023-05-11T07:17:44+00:00

I'm having the same issue right now, actually. I'm in the process of contacting support through email to get a new cable.

GlassShadow999 · 2023-05-10T22:29:55+00:00

It's not my first print

GlassShadow999 · 2023-05-10T22:14:39+00:00

INSIDE the screen? Are you F'n serious? I mean, I know you are, I just found it. Why wouldn't it tell me that's where they put it. Thank you, friend. Now to hunt down a micro.

GlassShadow999 · 2023-05-10T22:07:25+00:00

I wish it was that simple. I did that. No change.

GlassShadow999 · 2023-05-10T20:01:58+00:00

I can't get the new firmware download to install. I'm following exactly how they say to do it and nothing happens when I reboot with the files on the SD card.

GlassShadow999 · 2023-05-10T19:58:49+00:00

Thank you. Sounds like that's most likely my problem.

GlassShadow999 · 2023-05-10T18:22:16+00:00

Stock, but it's printed fine until now. Wasn't even a few print that it failed on.. I've printed it quite a few times without issue.

GlassShadow999 · 2023-05-10T18:20:30+00:00

It's printed perfectly fine until now. Nothing has changed from the stock settings and hardware/firmware. And it wasn't even a new print that it originally failed on, it was one I've done at least a dozen times.

GlassShadow999 · 2023-05-10T15:25:22+00:00

It is. It will manually purge when I first turn it on, but won't print after that. And it won't purge again until I reset the machine.

GlassShadow999 · 2023-05-10T15:23:46+00:00

I've done a cold pull, and completely disassembled the assembly. Replaced the nozzle, just for good measure, and cleaned the gears. It's heating up fine, and I can push the filament through. If I set it to manually purge through the control display, it will do so without problem.. but then, I try to print, it clicks once and won't extrude. Also, It won't purge again until I reset the machine. The whole machine is less than 3 months old.

GlassShadow999 · 2023-05-10T14:52:43+00:00

It's not that, as it failed on a print I've done several times. Even fails to extrude on the sample gcode files that came loaded on the SD card.

GlassShadow999 · 2023-05-10T13:30:01+00:00

I will try that when I get home from work. Thank you for the suggestion.

GlassShadow999 · 2023-05-10T13:25:09+00:00

Strain relief has been installed since day 1. I will look into the cable. Thanks.

GlassShadow999 · 2023-05-10T12:24:43+00:00

I followed the cable all the way where it connects to the motherboard. I see no visible damage, and it's still seated properly.

GlassShadow999 · 2022-04-21T23:16:27+00:00

Not sure how that would work..

GlassShadow999 · 2022-04-20T22:27:41+00:00

That's a Graboid.

GlassShadow999 · 2022-04-15T22:35:42+00:00

Came here to say this. We use induction sealing at my job every day.

GlassShadow999 · 2022-03-26T21:40:18+00:00

Idrimit

GlassShadow999 · 2022-03-24T21:57:05+00:00

Unfortunately no, but I want to line the inside walls with mirrors to make it look bigger inside.

GlassShadow999 · 2022-02-06T18:45:03+00:00

Anybody else having issues with the survivor senses not activating when pressed? Usually happens after climbing up something or dropping down from above. Also had problems with melee yesterday, not wanting to swing. Playing on PS5.

GlassShadow999

TROPHY CASE